Substrate integrated waveguide pedestal filtering-antenna and -arrays for 5G radio frequency front-ends

Abstract This paper presents the design, manufacturing, and measurement of a novel substrate integrated waveguide (SIW) pedestal filtering antenna solution for use in 5G New Radio sub-6 GHz communications. Miniaturization is achieved through the use of SIW pedestal resonators and integration of the radiating element into the filter design, resulting in higher order suppression. The design generates a third order filtering response utilizing SIW pedestal resonators and a patch antenna element. The manufactured SIW pedestal filtenna achieves a 10 dB return loss bandwidth of 4.29% about a center frequency of 3.63 GHz, and a boresight gain of 3.66 dBi. Using the SIW pedestal filtenna elements, two array configurations are measured, a 1 × 1 linear array and 2 × 2 planar array. Beam-steering capability for the linear array is demonstrated in simulation, while the 2 × 2 array is shown to be suited to both dual- and single-mode operation.


Introduction
High-level integration of radio frequency front-end components has the potential to yield miniaturized, cost-effective, and low loss solutions.Many modern telecommunication solutions aim toward multiple input and output (MIMO), where often a large number of antennas are implemented to increase the gain and spatial selectivity.Miniaturization of the front-end components are therefore required.As spectrum allocations and base station roll-out increase, the need for adequate band selection, harmonic and non-linear product filtering, and radio frequency interference (RFI) mitigation increases.From a system point of view, various options exist for the placement of filtering components.Adjacent placement of antenna and filter can enable final stage suppression of unwanted emissions, adequate band selection, and RFI mitigation.The integrated solution of antenna and filter is called a filtenna, where the advantages, compared to an unintegrated solution, include miniaturization, improved transition loss, direct impedance matching, and manufacturing cost reduction.Though it is not always desirable to place a passive element adjacent to the antenna due to noise figure and loss, the associated loss may be minimized through the use of high quality factor (Q) resonators.
Several published filtenna solutions are implemented using planar technologies, such as microstrip [1][2][3] and substrate integrated waveguide (SIW) [4,5].The high Q, cost, and ease of integration with other planar components, make SIW solutions attractive for use in filtenna design.Several published filtenna works implement SIW cavities in full-or half-mode operation, single-or multi-layer structures, and with a variety of radiating elements.In [6], a SIW cavity-backed filtenna is presented with a stacked patch antenna configuration, while a half-mode SIW duplex filtenna with slot radiating elements is shown in [7].Another slot antenna example is the SIW cavity-backed bow-tie slot filtenna shown in [9].In [4], a multilayered SIW filtenna is proposed in which two vertically stacked SIW cavities are integrated with a complementary split ring resonator as the antenna.The manufactured filtenna is approximately 7 × 7 cm 2 and achieves a −10 dB S 11 bandwidth of 6.3%, and a gain of 6.73 dBi.A single-layer SIW filtenna with parasitic patch is presented in [10], where a half-mode SIW cavity resonator is used.The manufactured filtenna is approximately 8 × 5 cm 2 in size and achieves a 5.1% −10 dB S 11 bandwidth and gain of 6.3 dBi at 2.77 GHz.Another single layer SIW filtenna is presented in [11], where a slot antenna and SIW cavity are integrated.Mixed-mode coupling is used to create radiation nulls on both sides of the passband.The manufactured filtenna is approximately 2 × 2 cm 2 and achieves a −10 dB S 11 bandwidth of 2.53% from 9.44 to 9.68 GHz, with a maximum realized gain of 5.8 dBi.
SIW solutions offer an improvement in quality factor compared to microstrip solutions, but at the cost of a larger size [12].The SIW pedestal resonator was first proposed in [13], and 15, offers a reduction in size of the SIW resonator with Q-factors comparable to standard SIW cavity resonators.While single layer structures are possible for standard SIW resonators, the pedestal resonator requires multi-layer manufacturing.The pedestal resonator lends itself well to achieve both positive and negative coupling for coupled resonator filter design, as shown in [14].The pedestal resonator can therefore provide a high Q option for direct integration with antenna solutions.
This work proposes a novel SIW pedestal filtering antenna solution for use in the 5G sub-6 GHz communications.Miniaturization is achieved through integration of the radiating element into the filter design, resulting in higher order suppression.The design generates a third order filtering response utilizing two SIW pedestal resonators and one patch antenna element.The manufactured SIW pedestal filtenna achieves a 10 dB return loss bandwidth of 4.29% about a center frequency of 3.63 GHz, and a gain of 3.66 dBi.The element is also tested in a 4 element linear array configuration and a 4 element planar array configuration to demonstrate the applicability to 5G radio frequency front-ends.
An earlier version of this paper was presented at the 2022 16th European Conference on Antennas and Propagation and was published in its Proceedings [15].This is an extension of the work and includes further tests on the single element, a new array configuration, and beam-scanning and dual-mode capability tests on the arrays in simulation.Details on the filtenna design is provided in Section 'Filtenna design', the prototype simulations and measurements are shown in Section 'Filtenna prototype', where a comparison with other published works is included.The linear and planar array setups, radiation pattern measurements, and beam-scanning and reconfigurability are provided in Section 'Filtenna arrays'.

Filtenna design
For the initial prototype synthesis, a 3 rd order Chebyshev response and in-line coupled resonator topology are chosen, with a reflection coefficient of −10 dB.The filter −3 dB band is chosen from 3.45 to 3.60 GHz for C-band operation, which is a 4.26% bandwidth about a center frequency of 3.52 GHz.The coupling matrix of the synthesized filter, obtained through Filter Designer 3D in CST, is given in Table 1, where S and L represent the source and load respectively, and the values in the first row and column represent the resonator number.For example, a bandwidth normalized coupling coefficient of 0.7631 is required between resonator 1 and 2. A positive coupling coefficient means the net field coupling is predominantly magnetic field, or inductive, coupling.A negative coupling coefficient means a predominantly capacitive coupling is required.
The desired response is realized by means of a SIW pedestal filtenna structure with three coupled resonators.Two resonators are SIW pedestal resonators, and the third resonator is a patch antenna element.The pedestal resonators require a multilayer stackup containing three copper layers, two dielectric (Mercurywave core) layers, and a prepreg layer (PrePreg 1080) for adhesion.The stackup is shown in Fig. 1, where the dark colors (labelled M1-3) are copper and the others dielectric or prepreg.The patches of the pedestal resonators are in the center copper layer (M2), connected to the bottom ground (M1) with one blind via each.The patch antenna is on the top copper layer (M3) with its ground on the bottom copper layer (M1).The proposed filtenna prototype, details on the center layer (M2) and vias, and the input coupling structure are shown in Figs. 2 to 4, respectively.
For the connection to the antenna and a coaxial to planar transition, two planar to SIW transitions are included.The SIW cavity is formed by a single row of vias.The co-planar transmission lines couple magnetically to the SIW pedestal resonators by means of a through via, shown in Fig. 4. The pedestal resonator's magnetic field concentrates around the pedestal post, below the pedestal patch, while its electric field is maximum above the pedestal patch.The adjacent placement of two pedestals, as shown in Fig. 3, yield net magnetic inter-resonator coupling.The desired inter-resonator coupling factor between the two SIW pedestal resonators, resonators 1 and 2, is first obtained using the evenand odd-mode frequencies in the eigenmode solver of CST, which yielded 0.034 compared to the ideal 0.033 obtained when multiplying the value in Table 1 by the bandwidth.
Port 1 (co-planar line toward connector) is 50 Ω, while port 2 (co-planar line toward antenna) is 75 Ω.The port 1 loaded quality   factor is extracted and confirmed from the CST frequency domain solver using the group delay.The extracted value for the loaded quality factor at port 1 is 35.10, while the ideal case based on Table 1 is 36.45.The port 2 via, 75 Ω line, tapered line, and antenna together form an inverter, resonator and load for the 3 rd order Chebyshev response.The dimensions are found iteratively, since the final resonator and load are both due to the patch antenna and cannot be separated.The patch corners are rounded to provide a slightly wider resonance bandwidth of the antenna resonator.A patch with a narrower bandwidth causes rounding of the passband edges of the integrated filtenna response.This is due to the matching circuit limitation (Bode-Fano criteria).Compared to a standard patch antenna, this design enables improvement in roll-off characteristic.Using group delay tuning and Filter Designer 3D, which extracts the coupling matrix values from the simulated S-parameters, the SIW pedestal filtenna model is realized.Figure 2 in combination with Table 2 show the external dimensions of the designed filtenna.The radiation patterns of the two best performing filtennas (2 and 4) are measured using the setup in Fig. 8 and a waveguide probe (2.6 − 3.95 GHz).The measured and simulated radiation patterns for horizontal and vertical planes are shown in Figs. 9 and 10, respectively.The z-axis is normal to the patch antenna surface and the 0 • angle for both plots is in this direction.The antenna beam tilt of 15 • downward in elevation, as seen in Fig. 10, is due to the top ground plane layer.The difference in ripple between the simulated and measured traces is attributed to structural differences, since the cable, connector and positioner are not included in the simulation.In terms of back radiation, the filtenna achieves a magnitude of around −19 dB for the back lobe.This is 24 dB below the maximum gain point.For the side radiation, there is a maximum at El = 135 • which gives a side lobe level of −10.7 dB.Both these values were extracted from the simulation.

Filtenna prototype
A summary of the performance of the measured and simulated filtenna is provided in Table 3, where the gain is determined at boresight using the three antenna method.A measurement probe (WR-284) and two different manufactured SIW filtenna elements (filtenna 2 and 4) are used.It should be noted that this is not the maximum gain point, since the beam is tilted      down slightly.The maximum gain may be approximated using the radiation pattern.At a downwards tilt of 15 • the normalized realized gain is 0.5 dB higher, which means the maximum gain is approximated as 4.16 dBi, while the simulation yields 4.43 dBi.While a commonly used patch antenna has a typical gain of 5-8 dBi [8], the filtenna achieves 4.43 dBi in simulation.Simulating the filtenna's patch antenna element alone, fed with a discrete port, gives a gain of 6.44 dBi.Recalling that the cut SIW filter structure has a transmission coefficient of −2.8 dB, as shown in Fig. 6, an unintegrated solution would therefore yield a gain of 3.6 dBi.However, a higher gain is achieved in both simulated and measured case for the filtenna, due to the integrated design and functionality.
As an extension to the previous work, the gain as a function of frequency is measured.The simulated and measured case is plotted in Fig. 11.To increase the simulated model accuracy, the connector is added.The measurement is made on filtenna 2. Compared to the simulation, the measured realized gain shows a slight frequency offset, but a similar behavioral profile versus frequency.This frequency offset is also visible in the filtenna response as seen previously in Fig. 7. Here, for filtenna 2, the edges of the S 11 also have an offset compared to the simulation model.
However, there are some points in which the measurement is performing better, achieving a gain that is up to 0.32 dB higher than the simulation, including consideration for the frequency shift.This difference in gain is attributed to several factors.First, the maximum gain is not toward boresight, but at the aforementioned −15 degrees in elevation.Given a difference in measured gain of 0.34 dB between the boresight and −15 degree points, an upward tilt error of less than 15 degrees during the measurement could have resulted in a higher measured versus simulated gain.This upward tilt error likely resulted from overcompensation for cable tension pulling the top of the antenna forward.Another factor, albeit seemingly smaller, is the measurement tolerance while determining the distance for the three antenna method.Furthermore, there will also be an amplitude variation due to cable movements for measuring the path loss.These measurement tolerance estimations are shown via the shaded area in Fig. 11, representing a 0.5 dB error.A summary of the gain vs. frequency results is given in Table 4.The difference in the simulated gain versus what is shown in Table 3 is due to the connector addition.There is a slight difference between the center frequency and bandwidth when calculated using the −10 dB points in S 11 versus using the −3 dB points in Fig. 11, evident from the difference between Tables 3 and 4.This can be attributed to the rounding of the edges in Fig. 11 and the asymmetry in S 11 as shown in Fig. 7.
A comparison between published filtennas and this work is given in Table 5. Frequency, bandwidth, gain and size are provided.In this case the data in Table 3 is used for the SIW pedestal filtenna.It is clear that a competitive size is achieved, but the gain is lower than the cited works.While [4], [11],and [16] utilize slot antennas, [10] implements a patch antenna.This work, [4] and [16] have third order filtering with two SIW resonators, while [10] and [11] have second order responses with a single SIW cavity.

Filtenna arrays
Utilizing the SIW pedestal filtenna unit elements, two different array topologies are investigated: a linear and rectangular topology.The number of elements in each array is limited to 4. The filtenna performance in terms of reflection coefficient, gain, and beamwidth in azimuth and elevation is investigated and compared with simulation.During the measurements all other ports were loaded.

Linear array
A 1 × 4 linear pedestal filtenna array is created by placing the filtennas side-by-side.The center of the elements are therefore   Both these figures were generated by combining the embedded element patterns.The simulated maximum array gain is 9.3 dBi at 15 • lower than boresight.The measured −3 dB beamwidth is 22 • in the horizontal plane and 92 • in the vertical plane, while the simulation shows 24 • and 70 • respectively.The measured side-lobe level is below −12 dB versus −15 dB in simulation.The slightly higher side lobes can be explained using the (embedded) element patterns, which have a higher magnitude at the edges, as seen in Fig. 15.
Investigation of the beam-steering capability of the linear array is done and the result shown in Fig. 14.The steering is achieved by combining the element antenna patterns and applying artificial weights.While steering toward 40°, the maximum magnitude is found at around 38°.This steering deviation is due to the drop-off of the embedded element patterns outside of θ < 30°.
As with the previous array result, the main beam shows good resemblance to the simulation with a maximum difference of 1 dB, whereas the side lobes are higher for the measurements.Furthermore, when steering there is a seeming offset in the measurements and simulations when comparing the zero-crossings.As the same beam steering weights are applied to both the simulation and measurements, the difference can be found in the physical location of the antennas, which has a slight difference between the idealized planar simulation of the antenna and the practical measurement.There is also a deviation between the embedded element patterns from both the simulation and measurement.

Planar array
A 2 × 2 planar pedestal filtenna array is created by placing the filtennas with connectors pointing outwards.The center of the elements are substrate width (41.8 mm) in azimuth as well as in elevation, as shown in Fig. 12b.In this paper the results for a spacing between the two rows of antennas of λ/2 (41.8 mm) is discussed.The measurements were also done for the setup without clearance between the rows (<λ/2 separation), but besides the expected decrease in scan range, there were negligible differences.
In the measurement results, as seen in Fig. 16, the synthesized radiation pattern can be seen.This is achieved by adding a phase shift of 180 • to one of the rows to achieve a single main beam toward zenith.The second mode, for the multi-mode behavior,

Conclusion
This work shows a novel SIW pedestal filtenna and filtenna array, operational in the C-band for 5G sub-6 GHz communications.Miniaturization of the SIW cavities is achieved through the use of coupled pedestal resonators.The design is manufactured as a multilayered PCB including blind and through vias.The performance of the filtenna is comparable to other published works and good agreement is obtained between measured and simulated results.The measured gain at boresight was determined to be around 3.7 dBi, compared to the simulations at 3.9 dBi, with extra losses that can be account for in the measurement setup.Furthermore, a 1 × 4 linear and 2 × 2 planar pedestal filtenna array is demonstrated with possible application for future research and usage in sub-6 GHz 5G communications.Both beam-steering and dual-mode have shown to be possible when the SIW pedestal filtenna elements are utilized in an array.Improvements in gain and maximum beam direction should be considered in future designs.Additionally smaller radiating elements and structures can be investigated in future work to further miniaturize the overall structure.

Five
filtennas were manufactured by TraX Interconnect.Two of the manufactured filtennas, with edge-mount connectors, are shown in Fig.5.Due to tolerance on the manufactured height, a slight shift in frequency, from 3.52 GHz to 3.63 GHz, and de-tuning occurred.The de-tuning is mainly due to the use of different resonator types which have different sensitivity to height change, in other words, the path antenna tunes at a different rate to that of the SIW pedestal resonators.To confirm the height change of 0.08 mm (thicker), one of the manufactured filtennas was cut to remove the antenna, leaving only the two SIW resonators, a 50 Ω input and 75 Ω output.The cutting plane is shown on Fig.2.A 50 Ohm SMA connector is added to each port for the measurement.The simulated and measured results of the cut filter, including height compensation in simulation, is shown in Fig.6.As expected, the impedance mismatch is evident in the 75 Ω port's reflection coefficient.The transmission coefficient for the cut filter section is −2.8 dB at 3.63 GHz.The agreement between the simulated and measured response confirms that including a height change of 0.08 mm in the simulated model will more accurately represent the manufactured prototype.Implementation of the height change in the filtenna simulations showed that 0.8 mm should be cut from the top edge of the patch to tune the filtenna.Filtenna 5 in Fig.5shows the cut top edge.The results for the tuned filtennas are presented in Fig.7.Filtennas 1, 2, 4, and 5 were tuned correctly, while filtenna 3 was slightly over-tuned.The measured filtennas achieve a −10 dB bandwidth (BW) of 156 MHz (4.29%), at a center frequency of 3.63 GHz.

Figure 6 .
Figure 6.Simulated and measured 2 nd order filter response.

International
Journal of Microwave and Wireless Technologies substrate width (41.8 mm) apart, as shown in Fig. 12a, which is 0.5 mm more than half the free space wavelength at the center frequency.The measured and simulated array pattern in the vertical and horizontal plane are shown in Figs. 13 and 14 respectively.

Figure 16 .
Figure 16.Normalized radiation pattern of 2 × 2 Array, synthesized using the measured embedded element patterns.

Figure 17 .
Figure 17.Normalized radiation pattern of 2 × 2 array of the E-Plane, synthesized using the measured embedded element patterns, showing the multi-mode behavior.

Table 2 .
Filtenna dimensions with the symbols referring to Figs.2 and 3

Table 4 .
Filtenna gain vs freq performance at boresight comparison