Data characterizing tensile behavior of cenosphere/HDPE syntactic foam

The data set presented is related to the tensile behavior of cenosphere reinforced high density polyethylene syntactic foam composites “Processing of cenosphere/HDPE syntactic foams using an industrial scale polymer injection molding machine” (Bharath et al., 2016) [1]. The focus of the work is on determining the feasibility of using an industrial scale polymer injection molding (PIM) machine for fabricating syntactic foams. The fabricated syntactic foams are investigated for microstructure and tensile properties. The data presented in this article is related to optimization of the PIM process for syntactic foam manufacture, equations and procedures to develop theoretical estimates for properties of cenospheres, and microstructure of syntactic foams before and after failure. Included dataset contains values obtained from the theoretical model.


a b s t r a c t
The data set presented is related to the tensile behavior of cenosphere reinforced high density polyethylene syntactic foam composites "Processing of cenosphere/HDPE syntactic foams using an industrial scale polymer injection molding machine" (Bharath et al., 2016) [1]. The focus of the work is on determining the feasibility of using an industrial scale polymer injection molding (PIM) machine for fabricating syntactic foams. The fabricated syntactic foams are investigated for microstructure and tensile properties. The data presented in this article is related to optimization of the PIM process for syntactic foam manufacture, equations and procedures to develop theoretical estimates for properties of cenospheres, and microstructure of syntactic foams before and after failure. Included dataset contains values obtained from the theoretical model.

Value of the data
The tensile test results on syntactic foams produced by industrial scale injection molding machine are provided. The syntactic foams utilize fly ash cenospheres as filler material.
The experimental results on tensile testing can be used by industry professionals for development of syntactic foams for specific applications.
Theoretical models presented in the work can help researchers and industry professionals in predicting the properties of various compositions of syntactic foams and reduce experimentation.
The data can be used in design and evaluation of consumer products for manufacture with this lower-cost lightweight material.
Optimization data on industrial scale machine for syntactic foam manufacture can help other industries to adopt similar practices.

Data
Data presented in the article is pertaining to injection molding of fly ash cenosphere reinforced thermoplastic syntactic foam. High density polyethylene (HDPE) is used as the matrix material [1]. Cenospheres, which are an environmental pollutant, replace expensive HDPE in developing the syntactic foam components. The data contained in this brief consists of properties of raw materials, injection machine parameters, tensile test raw data and processed results, and micrographs of the material. In addition, images of prototype components are also provided.

Test equipment
Tensile testing was performed using a Zwick/Roell Z020 UTM with a 20 kN load cell in displacement control mode. Constant crosshead displacement rate is maintained at 50 mm/min. Stress and strain are calculated from load and displacement data.
Scanning electron microscope (JSM 6380LA, JEOL, Japan) is used for microstructural analysis. All the samples are sputter coated using JFC-1600 auto fine coater (JEOL, Japan).
Nikon D7000 camera with Nikkor 35 mm f/1.8 and Tokina AT-X Pro 100 mm f/2.8 macro lens are used for imaging fractured features.

Raw materials
The syntactic foams tested in this work were fabricated using high density polyethylene (HDPE, Reliance Polymers, Mumbai, India) as the matrix and fly ash cenospheres (Censosphere India Pvt. Ltd., Kolkata, India) as the hollow filler. Chemical and sieve analyses of the cenospheres are shown in Table 1.

Syntactic foam fabrication method
The constituents are mechanically mixed before being fed into a polymer injection molding machine and molded into ASTM D638-conforming tensile bars. The specifications of the injection Table 1 Chemical, physical and sieve analysis details of cenospheres n .

Physical properties
Chemical analysis (%) Sieve analysis   Table 2 and the process parameters are presented in Table 3. Syntactic foams containing 0% (HDPE), 20% (HDPE20), 40% (HDPE40), and 60% (HDPE60) by weight of cenospheres are fabricated. Fig. 1 shows a micrograph of HDPE60. Uniform dispersion of the hollow spheres in the HDPE matrix is observed in this micrograph, which affirms the feasibility of manufacturing syntactic foams using injection molding at high filler loadings (up to 66.4 vol% of cenospheres).

Tensile characterization
The load and displacement data are acquired from the tensile test. These data are used to calculate the stress-strain curves for each specimen shown in Fig. 2. The data used to produce these curves are included in the data folder (Tensile-Data.xlsx). This data can be used to calculate the tensile modulus, ultimate tensile strength (UTS), elongation at UTS, fracture strain and fracture strength. The modulus is calculated as the slope in the elastic region.
Failure features of neat HDPE specimen tested under tensile loading are presented in Fig. 3. This figure shows a broom-like fracture front and deformation marks along the entire specimen gauge length. Macroscopic failure features of syntactic foams are presented in Fig. 4, which can be compared with the failure appearance of the neat HDPE resin. The failure of syntactic foams appears to be relatively brittle with only a little plastic deformation, which can be confirmed from the tensile stress-strain data. Table 3 Processing conditions for injection molded syntactic foam composites n .

Parameters
Typical value  A large number of surviving particles after the tensile test are visible in Fig. 5 for an HDPE40 specimen. The crack propagation occurs mainly in the matrix resin. Defects in the cenosphere wall, non-spherical shape, and poor particle-matrix interfacial adhesion are observed in Fig. 5.
The optimized parameters for the industrial scale polymer injection molding machine are used to cast prototype parts shown in Fig. 6. These parts include narrow sections, screw threads, and holes showing the possibility of casting complicated parts with syntactic foams.

Theoretical modeling
A theoretical model for syntactic foams is presented that is used in a parametric study to determine the effective properties of the cenospheres from the experimental data on syntactic foams. The Porfiri-Gupta model involves solving for an infinitely dilute dispersion and using a differential scheme to extend the results to high particle loading [2,3]. The general expression of the differential scheme for elastic modulus is given as where E c and ν c are Young's modulus and Poisson's ratio of the ceramic particle wall, and E m and ν m are the modulus and Poisson's ratio of the matrix material. In addition, Φ f represents cenospheres volume fraction and Φ m denotes the maximum packing factor of particles, taken to be 0.637, which represents the random packing factor of equal size spheres. The parameter η is the radius ratio of the hollow particles, defined as the ratio of the inner radius to outer radius. The full formulation of the model is available in [2]. A parametric study is conducted by numerically solving the model for different input parameters and comparing with the experimental results to estimate the properties of cenospheres. A set of solutions for the elastic modulus as a function of the volume fraction of particles are given in the included data (Porfiri-Gupta-Model.xlsx).  As the properties of the ceramic wall material needed for the model are not known, they are estimated using the approach demonstrated by [4] using data for the particular grade of particles used in fabrication of the composites in this work ( Table 1). The presence of minor constituents is ignored, and the properties of the major constituents are taken as shown in Table 4. The elastic modulus of the ceramic wall material is found by where ϕ i and E i are the volume fraction and elastic modulus of each component. Density and Poisson's ratio can also be found using equations of similar type. The ceramic properties obtained by this method are presented in Table 4. Assuming that the cenosphere wall thickness is uniform and is fully dense, the value of η can be determined by where ρ TPD is the true particle density and ρ c is the density of the ceramic. The value of η is found to be 0.90 for the cenospheres used in these composites. The approaches used in determining the properties of the cenospheres ignore the presence of defects in the walls and thus lead to higher predictions than the actual modulus. In order to obtain an estimate of the effective properties of the cenospheres with defects, a parametric study is conducted using the theoretical model. In the first step the cenosphere wall modulus obtained from the rule of mixtures is used while the radius ratio is varied to minimize the difference between the model and experimental data. Conversely the radius ratio obtained from density measurements is kept constant while the ceramic modulus parameter is varied to obtain good fitting with the experiments. This generates two sets of effective properties for the cenospheres: E c ¼ 157 MPa with η¼0.995, and E c ¼7.5 GPa with η¼0.9. The effective modulus of an equivalent solid sphere E is found using [5] E ¼ Both of the pairs of cenosphere properties found in the parametric study yield an effective modulus of 1.20 GPa due to the presence of defects in their walls and other irregularities. Eqs. (1)- (3) can be used to predict the properties of hollow particles and syntactic foams in a similar manner with other types of raw material.