Elsevier

Acta Physico-Chimica Sinica

Volume 24, Issue 12, December 2008, Pages 2191-2197
Acta Physico-Chimica Sinica

ARTICLE
Preparation and Characterization of TiO2 Nanotube Arrays via Anodization of Titanium Films Deposited on FTO Conducting Glass at Room Temperature

https://doi.org/10.1016/S1872-1508(08)60082-0Get rights and content

Abstract

Self-organized TiO2 nanotube arrays with micro-scale length were prepared on fluorine-doped tin oxide (FTO) conducting glass in NH4F/glycerol electrolyte by electrochemical anodization of pure titanium films deposited by radio frequency magnetron sputtering (RFMS) at room temperature. The samples were characterized by means of field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and photoelectrochemistry methods. The results showed that Ti films prepared at the condition of Ar pressure 0.5 Pa, power 150 W, and 0.5 h at room temperature possessed the zone T model structure with good homogeneity and high denseness. When the anodization time was prolonged from 1 to 3 h at the voltage of 30 V, the pore diameter of TiO2 nanotubes increased from 50 to 75 nm, and the length increased from 750 to 1100 nm and then gradually decreased to 800 nm, while their wall morphology changed from smooth to rough. Also with increasing the anodization voltage, the pore diameter became larger, and the remaining oxide layer reduced, which could be easily removed by ultrasonic-chemical cleaning in 0.05% (w, mass fraction) diluted HF solution. Moreover, the photocurrent response curves and electrochemical impedance spectroscopy (EIS) results indicated that UV-illumination clearly enhanced the effective separation of the electron-hole pairs and the crystallized electrodes from the annealing treatment of as-anodized electrodes at 450 °C exhibited a better photoelectrochemical performance.

References (24)

  • J.M. Macak et al.

    Chemical Physics Letters

    (2006)
  • D.J. Yang et al.

    Materials Letters

    (2008)
  • X.F. Yu et al.

    Sensors and Actuators B

    (2008)
  • G.K. Mor et al.

    Solar Energy Materials and Solar Cells

    (2006)
  • K.S. Raja et al.

    Electrochemistry Communications

    (2007)
  • J.M. Macak et al.

    Journal of Electroanalytical Chemistry

    (2008)
  • A. van der Drift

    Phillips Res. Rep.

    (1967)
  • J.A. Thornton

    Ann. Rev. Mater. Sci.

    (1977)
  • B.A. Movchan et al.

    Phys. Met. Metallogr.

    (1969)
  • I. Petrova et al.

    J. Vac. Sci. Technol. A.

    (2003)
  • G.K. Mor et al.

    Adv. Funct. Mater.

    (2005)
  • G.K. Mor et al.

    Nano Lett.

    (2006)
  • Cited by (35)

    • Semi-transparent ordered TiO <inf>2</inf> nanostructures prepared by anodization of titanium thin films deposited onto the FTO substrate

      2016, Applied Surface Science
      Citation Excerpt :

      Although the applied voltage in the case of O2-anodization procedure equals 40 V, much higher current densities are registered during the electrochemical process performed under 10 V in water solution. Such behaviour results from the high viscosity coefficient of ethylene glycol, indicating that anodization process is controlled by diffusion [28]. As it is known, the diffusion constant is inversely proportional to the viscosity, and thus a lower growth and a chemical dissolution rate of the formed nanostructure are obtained in viscous electrolytes.

    • Wettability, structural and optical properties investigation of TiO<inf>2</inf> nanotubular arrays

      2016, Materials Research Bulletin
      Citation Excerpt :

      The problem is owing to the inappropriate illumination from the cell’s backside, where intensity of light loses significantly when it travels through the counter electrode, platinum coating and the redox mediator system [8]. Hence, it is vital to improve methods for construction of highly ordered TiO2 nanotubes from titanium thin films on any substrate like glass [9] silicon [10] and conducting glass [11–14]. To provide a thin film of titanium many techniques are available such as physical vapor deposition (PVD) magnetron sputtering technique, thermal diffusion (TD), chemical vapor deposition (CVD) and pulsed laser deposition.

    • Effect of substrate temperature and deposition rate on the morphology and optical properties of Ti films

      2013, Applied Surface Science
      Citation Excerpt :

      To overcome this restriction, one can control the deposition parameters such as inert gas pressure, sputtering power, substrate bias, and deposition rate. It is found that increasing power and negative substrate bias as well as decreasing inert gas is helpful to achieve a denser and more uniform film [9–11]. Controlling the deposition parameters (power, substrate bias, and deposition rate) leads to the development of structure zone model (Thornton model) which classifies the deposited coatings as a function of Tsub/Tm and the inert gas pressure [12].

    • Metal oxide nanoscience and nanotechnology for chemical sensors

      2013, Sensors and Actuators, B: Chemical
      Citation Excerpt :

      The formation of nanotubular arrays in neutral electrolytes has been recently investigated to overcome this drawback [33]. In fact, the chemical dissolution of the oxidized TiO2 is essentially suppressed in neutral electrolytes, in comparison with acidic aqueous solutions, allowing formation of longer nanotubes [34,35]. We have obtained TiO2 tubular arrays on stiff and flexible substrates (Fig. 4) [29,36].

    • Defect minimization and morphology optimization in TiO <inf>2</inf> nanotube thin films, grown on transparent conducting substrate, for dye synthesized solar cell application

      2012, Thin Solid Films
      Citation Excerpt :

      It also prevents direct SEM characterization of TNT tops, which is necessary to optimize the voltage parameters to obtain the required tube diameter. Similar “anomalies” of Ti anodization [19,28] were described in the literature and methods like sonication in diluted HCl or immersion into diluted HF solutions were proposed to remove it [29]. However, it's not always possible to efficiently remove amorphous debris from the TNT top surface—some areas remain covered even after repeated sonication in acid.

    View all citing articles on Scopus

    The project was supported by the Natural Science Foundation of Jiangsu Province (BK2004129) and the Aeronautical Science Foundation of China (04H52059).

    View full text