Downhole heavy crude oil hydroprocessing

doi:10.1016/0926-860X(96)00003-8

Applied Catalysis A: General

Volume 140, Issue 1, 20 June 1996, Pages 1-16

https://doi.org/10.1016/0926-860X(96)00003-8 Get rights and content

Abstract

Several processing options are being proposed to accomplish near well-bore, downhole (in-situ) hydroprocessing of heavy crude oils. These processes are designed to pass crude oil over a fixed bed of catalyst, the catalyst being placed by conventional reservoir engineering methods. The presence of water or brine and the need to provide heat and reactant gases in a downhole environment impose challenges not present in conventional processing. In order for an in-situ process to be successful, there is a need to assess if hydroprocessing reactions under these unusual conditions are possible; and if so, how much upgrading can be obtained at processing conditions that can reasonably be obtained in an in-situ environment. Both continuous flow and batch reactor systems were used for assessing in-situ hydroprocessing of heavy crude oils. Processing conditions, including oil/water ratios, temperatures, pressures, and hydrogen flow-rates, were those expected to be achievable in a downhole environment. For the particular heavy Middle-Eastern crude oil studied, hydrodesulfurization follows pseudo-first order kinetics; activity is not catalyst dependent but instead appears to be limited by the reactivity of the feed. Additionally, from 20 to 30% of the sulfur contained in this particular crude oil consists of thermally labile sulfur; the amount of which removed remains constant provided a minimum processing temperature is attained. Density of the product decreases almost linearly with increasing reaction temperature. Reduction of hydrogen partial pressure results in a decrease in hydrodesulfurization, probably due to hydrogen starvation. Upgrading reactions occur in a sufficiently short contact time to allow for conventional oil-well production rates. These results indicate that in-situ hydroprocessing is feasible from reaction and catalyst standpoints.

References (19)

E. Laurent et al.
J.G. Speight
M. Villalba et al.
U.S. Dept. of Energy DOE CONF-940450
(April, 1994)
D.M. Dean et al.
Bodcau in-situ combustion project final report
U.S. Dept. of Energy ET-12057-9
(December, 1982)
E.J. Hoffman
Energy Sources
(1989)
A. Gregoli, U.S. Patent 4,501,445 (1985) to Cities Service...
O. Stine, U.S. Patent 4,444,257 (1984) to...
O. Stine, U.S. Patent 4,448,251 (1984) to...
P.R. Stapp
In-situ hydrogenation
National Institute for Petroleum and Energy Research, NIPER-434
(1989)

There are more references available in the full text version of this article.

Cited by (52)

Other thermal methods
2023, Thermal Methods
The steam-based and in situ combustion methods are classical, well-known, and routine thermal methods for recovering heavy crude oils in the oil industry. The limitations and challenges of these methods have motivated researchers to explore new thermal methods for increasing oil recovery, eliminating the restriction of conventional methods, expanding the applicability of thermal methods for broader situations, and lowering the cost of projects. These methods, which are different from traditional methods, are called unconventional or other thermal methods. This term is used because some of these methods are relatively novel, or fewer projects have been operated using these methods compared to conventional methods. These methods include deep Eutectic Solvents (DESs), in situ upgrading, electrical heating methods, novel wellbore configuration, and solar energy heating. This chapter explains these methods thoroughly, and other aspects, such as screen criteria, existing laboratory tests, upscaling, and field challenges, will also be reviewed.
Determination of the chemical compositions of heavy, medium, and light crude oils by using the Distillation, Precipitation, Fractionation Mass Spectrometry (DPF MS) method
2019, Fuel
Citation Excerpt :
Over the past decades, the quality of crude oil recovered from oil wells has been declining because much of the light crude oil has been already removed from the reservoirs, leaving behind heavier crude oil [1–3]. Unfortunately, heavier crude oil has a lower value because it is more difficult to process [4]. The formal classification of crude oil as heavy or light is based on the American Petroleum Institute (API) gravity, which is a measure for the density of the crude oil relative to water [5].
We have previously demonstrated that the Distillation, Precipitation, Fractionation Mass Spectrometry (DPF MS) method can be used to characterize crude oil at the molecular level by fractionating the crude oil into six different chemical classes and analyzing each class by using an optimized mass spectrometry method. In this study, the chemical compositions of five crude oil samples, including heavy, medium, and light crude oils with different API gravities, were determined using the DPF MS method. The gravimetric weight percentages of the six compound classes within each crude oil sample were also determined. In general, the heavier crude oils contained more asphaltenes and heteroaromatic compounds and less heavy, alkyl aromatic and volatile saturated hydrocarbons than the lighter crude oils. However, the only correlation found for API gravity and the gravimetric weight percentages of the entire compound classes was for the heteroaromatic compound class: crude oils with lower API gravities contained more heteroaromatic compounds. Determination of the total nitrogen content by using a controlled combustion experiment revealed only a poor correlation between the total nitrogen content and API gravity. No obvious correlations were found between API gravity and the amounts of the compounds with different elemental compositions in the whole crude oils. However, consideration of differences in the chemical compositions within the different compound classes revealed trends related to the API gravity. For example, a linear correlation was found for the decrease in the API gravity and the increase in the gravimetric weight percentage of the most abundant nitrogen-containing compounds (with the C_cH_hN elemental composition) in the heteroaromatic compound class, the class that contains most of these compounds. On the other hand, as the API gravity decreases, the nitrogen content outside the aromatic cores (or in another aromatic core) of the compounds in the heteroaromatic compound class increases. Further, as the API gravity decreases, the extent of unsaturation increases for the compounds in the heteroaromatic compound class. These findings correlate the API gravity of crude oil to the chemical composition of the heteroaromatic compound class. No correlations were found between API gravity and the chemical compositions of the other compound classes or the whole crude oil.
Composition of aquathermolysis catalysts forming in situ from oil-soluble catalyst precursor mixtures
2018, Journal of Petroleum Science and Engineering
Citation Excerpt :
Thus, aquathermolysis is an in situ upgrading technique of high viscous heavy hydrocarbons. The aquathermolysis has a common principle with internal combustion, low temperature oxidation and other methods – injection of various reagents into the heated reservoirs (Weissman and Kessler, 1996). Yet, heavy crude oil cools down after the production in downstream conditions and the viscosity rises again.
Increasing efficiency of thermal recovery methods of heavy oil through injection of destructive hydrogenation catalysts precursors is a relevant task. In this paper the composition and properties of the active binary catalysts, which formed from a mixture of oil-soluble iron-, nickel- and copper-based precursors have been studied by XRD, Mössbauer spectroscopy, SEM, EDX-mapping methods. Moreover, the efficiency of a mixture of the corresponding metals in reducing the content of heavy components (SARA) of heavy crude oil from Ashal'cha field (Republic of Tatarstan) have been investigated. Mössbauer spectroscopy and EDX-mapping detected the formation of not only spinel ferrites MFe₂O₄ (where M = Ni or Cu), but also individual oxides. Moreover, in case of nickel-based catalyst three phases are formed: magnetite FeO⋅Fe₂O₃, spinel ferrite NiFe₂O₄ and superparamagnetic finely dispersed phase of iron oxides (and probably nickel oxides). According to XRD results, the oxides formed in the first stage transform into nonstoichiometric spinel ferrites Cu_0.86Fe_2.14O₄ and Ni_1.43Fe_1.7O₄ under hydrothermal influences. It is related with the thermodynamically beneficial processes of conversion of this specific phase composition. Based on the SARA and elemental analysis of the initial and converted oil, it was found that catalytic aquathermolysis decreases the content of asphaltenes and resins (about 45%) in the presence of catalyst nanoparticles, which indicates an improvement in the quality of the heavy oil.
Fossil Fuels
2018, Comprehensive Energy Systems
Fossil fuels have always had the major share in the global primary energy consumption. Overall fossil fuel consumption increased approximately 51% in the period of 1995–2015, and it is predicted that the consumption will increase approximately 18% more in the period of 2015–35. It was observed that, in 1995, oil, natural gas, and coal had total primary energy consumption shares of 38%, 22%, and 26% (87% in total), respectively; that, in 2015, they had total primary energy consumption shares of 32%, 24%, and 29% (85% in total), respectively; and it is predicted that, by 2035, the shares will be 29%, 25%, and 24% (78% in total), respectively, having natural second place after oil, and that a 7% decrease in fossil fuels share in consumption is predicted in the global primary energy consumption. Even though the share of fossil fuel consumption has decreased and is predicted to decrease further, they will continue to hold the major share in the primary energy mix in the foreseeable future as more unconventional fossil fuels are explored. The highest change in fossil fuel consumption has happened and is predicted that it will continue to happen in natural gas, a cleaner fossil fuel compared to oil and coal; however, extraction of and burning all fossil fuel forms have serious environmental consequences, which will require further and closer attention as more unconventional fossil fuel resources are explored and their overall consumption expand further.
Fossil Fuels
2018, Comprehensive Energy Systems: Volumes 1-5
Fossil fuels have always had the major share in the global primary energy consumption. Overall fossil fuel consumption increased approximately 51% in the period of 1995–2015, and it is predicted that the consumption will increase approximately 18% more in the period of 2015–35. It was observed that, in 1995, oil, natural gas, and coal had total primary energy consumption shares of 38%, 22%, and 26% (87% in total), respectively; that, in 2015, they had total primary energy consumption shares of 32%, 24%, and 29% (85% in total), respectively; and it is predicted that, by 2035, the shares will be 29%, 25%, and 24% (78% in total), respectively, having natural second place after oil, and that a 7% decrease in fossil fuels share in consumption is predicted in the global primary energy consumption. Even though the share of fossil fuel consumption has decreased and is predicted to decrease further, they will continue to hold the major share in the primary energy mix in the foreseeable future as more unconventional fossil fuels are explored. The highest change in fossil fuel consumption has happened and is predicted that it will continue to happen in natural gas, a cleaner fossil fuel compared to oil and coal; however, extraction of and burning all fossil fuel forms have serious environmental consequences, which will require further and closer attention as more unconventional fossil fuel resources are explored and their overall consumption expand further.
A comparative study of fixed-bed and dispersed catalytic upgrading of heavy crude oil using-CAPRI
2015, Chemical Engineering Journal
Citation Excerpt :
After upgrading, they found that the produced oil sample (API gravity 16° and viscosity at 40 °C, 60 mPa s) was significantly upgraded compared to the Athabasca bitumen (API gravity 9.5° and viscosity 7680 mPa s). The delivery of nano-sized catalyst into the oil-bearing formation for in situ catalytic upgrading can be accomplished by injecting it as a slurry, pneumatically conveying into the MOZ or alternatively precipitated in situ using a suitable metal precursors [12,14,15]. The separation challenges can be resolved by inducing magnetic characteristics to the ultrafine particles to enhance magnetic separation [16].
CAtalytic upgrading PRocess In-situ (CAPRI) incorporated with Toe-to-Heel Air Injection (THAI) for heavy oil and bitumen recovery and upgrading was studied for fixed-bed and dispersed catalysts. The extent of upgrading was evaluated in terms of API gravity, viscosity reduction, impurity removal, and true boiling point (TBP) distribution. The test was carried out using Co-Mo/Al₂O₃ at temperature of 425 °C, pressure 20 bar, and residence time of 10 min. The dispersed catalyst was tested in a batch reactor. However, the residence time, catalyst-to-oil (CTO) ratios as well as the Reynolds numbers of both contacting patterns were kept the same to ensure dynamic similitude. It was found that the produced oil from dispersed ultrafine Co-Mo/Al₂O₃ catalyst (d_p = 2.6 μm) exhibited superior light oil characteristics and quality than that produced with the fixed-bed of pelleted Co-Mo/Al₂O₃ (1.2 mm diameter × 2–5 mm length). The API gravity of the feed oil was 13.8° and the produced oil showed an increase of 5.6° in the fixed bed and 8.7° with the dispersed catalyst. Unlike the fixed-bed of pelleted Co-Mo/Al₂O₃ which may suffer from diffusion limitations, rapid deactivation, and channelling effect, the ultrafine particles presented high surface area to volume ratio, reducing the chances of pore plugging, have more accessible reaction sites per unit mass, and lead to enhanced cracking of macromolecules. Moreover, the reduction of sulphur of 38.6% and (Ni + V) content of 85.2% in the produced oil show greater heteroatom removal compared to 29% (sulphur) and 45.6% (Ni + V) observed in the product from the fixed-bed.

View all citing articles on Scopus

View full text

Downhole heavy crude oil hydroprocessing

Abstract

U.S. Dept. of Energy DOE CONF-940450

Bodcau in-situ combustion project final report

U.S. Dept. of Energy ET-12057-9

Energy Sources

In-situ hydrogenation

National Institute for Petroleum and Energy Research, NIPER-434