Abstract
In this study, the effects of spraying nanoparticles with different geometries (nano-SiO2, nano-halloysite, and nano-montmorillonite) on surface characteristics of concrete pavement in terms of microstructure. The initial and final setting times of mixtures were determined to investigate the proper spraying time for applying on the pavement surface at early ages. To precisely investigate the microstructural properties, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and atomic force microscopy (AFM) were used. The results revealed that spraying nanoparticles improved the abrasion and skid resistance as well as transport properties of the concrete surface, especially at the initial setting time. According to the tribology testing, the surface friction coefficient of sprayed samples compared to the reference sample (not sprayed) was increased 28%, on average. AFM results verified that this growth is due to the improved surface roughness and van der Waals forces. Based on the FTIR results, the abrasion resistance of the samples gradually diminished by increasing the depth due to reduction of nanoparticles penetration, thus, reducing its positive effect. In addition, a good relationship with regression coefficient of 0.79 was found between the surface tensile strength and the abrasion resistance of the specimens.
Similar content being viewed by others
References
Mehta PK, Monteiro PJ (2017) Concrete microstructure, properties and materials. Copyright/Pub. Date: 2014 McGraw-Hill Education, ISBN: 9780071797870
Taylor PC, Kosmatka SH, Voigt GF (2006) Integrated materials and construction practices for concrete pavement: a state-of-the-practice manual
Silvestre J, Silvestre N, de Brito J (2016) Review on concrete nanotechnology. Eur J Environ Civil Eng 20(4):455–485
Shekari A, Razzaghi M (2011) Influence of nano particles on durability and mechanical properties of high performance concrete. Proc Eng 14:3036–3041
Zhang H, Zhao Y, Meng T, Shah SP (2015) The modification effects of a nano-silica slurry on microstructure, strength, and strain development of recycled aggregate concrete applied in an enlarged structural test. Constr Build Mater 95:721–735
Tiwari JN, Tiwari RN, Kim KS (2012) Zero-dimensional, one-dimensional, two-dimensional and three-dimensional nanostructured materials for advanced electrochemical energy devices. Prog Mater Sci 57(4):724–803
Said AM, Zeidan MS, Bassuoni M, Tian Y (2012) Properties of concrete incorporating nano-silica. Constr Build Mater 36:838–844
Du H, Du S, Liu X (2014) Durability performances of concrete with nano-silica. Constr Build Mater 73:705–712
Fallah S, Nematzadeh M (2017) Mechanical properties and durability of high-strength concrete containing macro-polymeric and polypropylene fibers with nano-silica and silica fume. Constr Build Mater 132:170–187
Farzadnia N, Abang Ali AA, Demirboga R, Anwar MP (2013) Effect of halloysite nanoclay on mechanical properties, thermal behavior and microstructure of cement mortars. Cem Concr Res 48:97–104. https://doi.org/10.1016/j.cemconres.2013.03.005
Kafi MA, Sadeghi-Nik A, Bahari A, Sadeghi-Nik A, Mirshafiei E (2016) Microstructural characterization and mechanical properties of cementitious mortar containing montmorillonite nanoparticles. J Mater Civ Eng 28(12):04016155
Ghoddousi P, Shirzadi Javid AA, Zareechian M (2018) Physical and chemical effects of siliceous particles at nano, micro, and macro scales on properties of self-consolidating mortar overlays. Constr Build Mater 189:1140–1154
Li H, Zhang M-h, Ou J-p (2006) Abrasion resistance of concrete containing nano-particles for pavement. Wear 260(11):1262–1266
Nazari A, Riahi S (2011) Abrasion resistance of concrete containing SiO 2 and Al 2 O 3 nanoparticles in different curing media. Energy Build 43(10):2939–2946
Gonzalez M, Safiuddin M, Cao J, Tighe S (2013) Sound absorption and friction responses of nanoconcrete for rigid pavements. Transp Res Rec J Transp Res Board 2369:87–94
Kupwade-Patil K, Cardenas HE, Gordon K, Lee LS (2012) Corrosion mitigation in reinforced concrete beams via nanoparticle treatment. ACI Mater J 109 (6)
Hou P, Cheng X, Qian J, Shah SP (2014) Effects and mechanisms of surface treatment of hardened cement-based materials with colloidal nanoSiO2 and its precursor. Constr Build Mater 53:66–73
Hou P, Cheng X, Qian J, Zhang R, Cao W, Shah SP (2015) Characteristics of surface-treatment of nano-SiO2 on the transport properties of hardened cement pastes with different water-to-cement ratios. Cement Concr Compos 55:26–33
Ardalan RB, Jamshidi N, Arabameri H, Joshaghani A, Mehrinejad M, Sharafi P (2017) Enhancing the permeability and abrasion resistance of concrete using colloidal nano-SiO 2 oxide and spraying nanosilicon practices. Constr Build Mater 146:128–135
ASTM C150 (2007) Standard specification for Portland cement. ASTM International, West Conshohocken
ASTM C33. Standard specification for concrete aggregate, vol. 04.02. Annual Book of ASTM Standard (1997) p. 132–5
ASTM C494 (2001) Standard specification for chemical admixtures for concrete, Annual book of ASTM standards, Philadelphia; 04.02, p. 261–9
ACI Manual of Concrete Practice (2000) Part 1: materials and general properties of concrete. American Concrete Institute, Farmington Hills
Madani H, Bagheri A, Parhizkar T (2012) The pozzolanic reactivity of monodispersed nanosilica hydrosols and their influence on the hydration characteristics of Portland cement. Cem Concr Res 42(12):1563–1570
Navarro-Blasco I, Pérez-Nicolás M, Fernández J, Duran A, Sirera R, Alvarez J (2014) Assessment of the interaction of polycarboxylate superplasticizers in hydrated lime pastes modified with nanosilica or metakaolin as pozzolanic reactives. Constr Build Mater 73:1–12
Bagheri A, Parhizkar T, Madani H, Raisghasemi A (2013) The influence of different preparation methods on the aggregation status of pyrogenic nanosilicas used in concrete. Mater Struct 46(1–2):135–143
ASTM C403 2008 Standard test method for time of setting of concrete mixtures by penetration resistance. ASTM Int https://doi.org/10.1520/C0403_C0403M-08
En 12390-3 (2009) Testing hardened concrete—part 3: compressive strength of test specimens. British Standards Institution, London
ASTM C1583 (2013) Standard test method for tensile strength of concrete surfaces and the bond strength or tensile strength of concrete repair and overlay materials by direct tension. Pull-off Method. https://doi.org/10.1520/C1583_C1583M-13
EN 1340 (2003) Concrete kerbs units. Requirements and test methods. European Standard
ASTM E303 (2013) Standard test method for measuring surface frictional properties using the british pendulum tester
Kashani MR, Behazin E, Fakhar A (2011) Construction and evaluation of a new tribometer for polymers. Polym Testing 30(3):271–276
Kashani MR, Nisiany RE (2011) Design, construction, and evaluation of rubber friction tester. Sci Technol 24(2):153–164
ASTM C1585-04 Standard test method for measurement of rate of absorption of water by hydraulic-cement concretes
EN B (2000) 12390-8. Depth of penetration of water under pressure. British Standards Institution, London
Valenta O (1970) From the 2nd RILEM symposium durability of concrete—in Prague. Matériaux et Construction 3(5):333–345
Milling A, Mulvaney P, Larson I (1996) Direct measurement of repulsive van der Waals interactions using an atomic force microscope. J Colloid Interface Sci 180(2):460–465
Duan P, Shui Z, Chen W, Shen C (2013) Effects of metakaolin, silica fume and slag on pore structure, interfacial transition zone and compressive strength of concrete. Constr Build Mater 44:1–6
Li Z (2011) Advanced concrete technology. Wiley, Hoboken
Li H, Xiao H-g, Yuan J, Ou J (2004) Microstructure of cement mortar with nano-particles. Compos Part B Eng 35(2):185–189
Qing Y, Zenan Z, Deyu K, Rongshen C (2007) Influence of nano-SiO 2 addition on properties of hardened cement paste as compared with silica fume. Constr Build Mater 21(3):539–545
Poon CS, Shui Z, Lam L (2004) Effect of microstructure of ITZ on compressive strength of concrete prepared with recycled aggregates. Constr Build Mater 18(6):461–468
Long A, Murray A (1981) Pull-off’ test for in situ concrete strength. Concrete 15:23–24
Singh L, Karade S, Bhattacharyya S, Yousuf M, Ahalawat S (2013) Beneficial role of nanosilica in cement based materials–a review. Constr Build Mater 47:1069–1077
Neville AM (1995) Properties of concrete. ISBN: 978-0-273-75580-7
Sherwood JA Effects of concrete mixture designs on skid numbers. In: Eighth international conference on managing pavement assetsfugrofederal highway administrationintervial ChileCAF-Banco de Desarrollo de America Latina, 2011. vol ICMPA169. Citeseer
Hall J, Smith KL, Titus-Glover L, Wambold JC, Yager TJ, Rado Z (2009) Guide for pavement friction. Transportation Research Board of the National Academies, Washington
Gohar R, Rahnejat H (2012) Fundamentals of tribology. World Scientific. books.google.com
Funding
No funding was received for this research.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Shirzadi Javid, A.A., Ghoddousi, P., Zareechian, M. et al. Effects of Spraying Various Nanoparticles at Early Ages on Improving Surface Characteristics of Concrete Pavements. Int J Civ Eng 17, 1455–1468 (2019). https://doi.org/10.1007/s40999-019-00407-4
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40999-019-00407-4