Abstract
The cylinder liner is regarded as the “ventricle” of the heart of the engine, and its performance plays a decisive role in the overall performance of the engine. V was added to improve the mechanical properties such as the strength and hardness of the super-large cylinder liner. Using optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Brinell hardness tester universal testing machine, the effects of the addition of V for gray cast iron microstructure and mechanical properties were investigated. The results show that after the addition of V, VC compounds can be produced in the matrix structure, the graphite structure and the pearlite structure are refined, and the pearlite sheet spacing is also significantly reduced. Mechanical performance has been significantly improved. The best overall performance was achieved at the content of 0.21 wt.% V, and Brinell hardness, compressive strength and tensile strength values are 421 HB, 1699 MPa and 501 MPa, respectively, which were increased by 78.5%, 64.8% and 61.6%. This is mainly because the V plays a role in fine-grain strengthening and precipitation strengthening of the alloy.
Graphical abstract
Similar content being viewed by others
References
W. Huang, P. Ren, Z. Zuo et al., High-cycle fatigue failure analysis of cast Al-Si alloy engine cylinder head. Eng. Fail. Anal. 127, 105546 (2021)
S. Kianfar, E. Aghaie, J. Stroh et al., Residual stress, microstructure, and mechanical properties analysis of HPDC aluminum engine block with cast-in iron liners. Mater. Today Commun. 26, 101814 (2021)
C. Thiagarajan, M. Prabhahar, S. Prakash et al., Heat transfer analysis and optimization of engine cylinder liner using different materials. Mater. Today Proc. 33, 778–783 (2020)
M.A. Irfan, D. Schwam, A. Karve et al., Porosity reduction and mechanical properties improvement in die cast engine blocks. Mater. Sci. Eng., A 535, 108–114 (2012)
I. Mitelea, I. Bordeau, E. Riemschneider et al., Cavitation erosion improvement following TIG surface-remelting of gray cast iron. Wear 496, 204282 (2022)
O. Oloyede, R.F. Cochrane, A.M. Mullis, Effect of rapid solidification on the microstructure and microhardness of BS1452 grade 250 hypoeutectic grey cast iron. J. Alloy. Compd. 707, 347–350 (2017)
S.M. Yoo, Y.S. Cho, C.C. Lee et al., Optimization of casting process for heat and abrasion resistant large gray iron castings. Tsinghua Sci. Technol. 13, 152–156 (2008)
A.N. Sudhakar, R. Markandeya, B. SrinivasaRao et al., Effect of alloying elements on the dry sliding wear behavior of high chromium white cast iron and Ni-hard iron. Mater. Today Proc. 60, 1303–1309 (2022)
T. Chotikarn, S. Janudom, P. Muangjunburee, et al. Sand mold design for high-phosphorus cast iron brake shoe casting. Inter Metalcast. (2022). https://doi.org/10.1007/s40962-022-00802-z
H.R. Abbasi, M. Bazdar, A. Halvaee, Effect of phosphorus as an alloying element on microstructure and mechanical properties of pearlitic gray cast iron. Mater. Sci. Eng., A 444(1–2), 314–317 (2007)
A.N. Sudhakar, R. Markandeya, B. Srinivasa Rao et al., Effect of alloying elements on the microstructure and mechanical properties of high chromium white cast iron and Ni-Hard iron. Mater. Today Proc. 61, 1006–1014 (2022)
M. Moonesan, A. Honarnakhsh raouf, F. Madah et al., Effect of alloying elements on thermal shock resistance of gray cast iron. J. Alloys Compd. 520, 226–231 (2012)
C. Khuntrakool, S. Janudom, P. Muangjunburee, N. Mahathaninwong, T. Chucheep, T. Chotikarn, A. Yodjan, Effects of chemical composition on microstructure and properties of high phosphorus grey cast iron brake shoe. Int. J. Metalcast. 16(3), 1221–1234 (2022)
S.H. Kim, E.R. Baek, B.K. Jang, The effect of vanadium addition on the fracture and wear resistance of indefinite chilled cast iron. Mater. Today Commun. 26, 101819 (2021)
Y. Liu, M. Martinón-Torres, J. Mei et al., Cast a different iron: Grey and mottled cast iron production in early China. J. Cult. Herit. 46, 184–192 (2020)
H. Liu, W. Qian, J. Chen, H. Chen, M.L. Chastain, M.R. Notis, Cast iron-smelting furnace materials in imperial China: macro-observation and microscopic study. J. Archaeol. Sci. 86, 50–59 (2017)
A.M.S. Noohi, N. Hamidnezhad, A. Safikhani et al., The formation mechanism of sweat phosphide in a new form and comparison with expansion scab in the gray cast iron castings. Inter Metalcast. 11, 347–355 (2017). https://doi.org/10.1007/s40962-016-0064-0
M. Cova, P. Livieri, R. Rizzoni et al., A preliminary investigation of strength models for degenerate graphite clusters in grey cast iron. Procedia Struct. Integrity 7, 446–452 (2017)
L. Qing-yi, Z. Xiao-fu, S. Yu-cheng et al., Quantitative models for microstructure and thermal conductivity of vermicular graphite cast iron cylinder block based on cooling rate. China Foundry 18(1), 52–59 (2021)
W. Wei, T. Jing, Y. Gao et al., Properties of a gray cast iron with oriented graphite flakes. J. Mater. Process. Technol. 182(1–3), 593–597 (2007)
S.H. Kim, E.R. Baek, B.K. Jang, The effect of vanadium addition on the fracture and wear resistance of indefinite chilled cast iron. Mater. Today Commun. 26, 101819 (2020)
A. Sl, B. Jhy, C. Shp et al., Effect of carbon content in steel powder feedstock on impact toughness and microstructure of additively manufactured cast iron by directed energy deposition. J. Market. Res. 15, 189–198 (2021)
S. Upadhyay, K.K. Saxena, Effect of Cu and Mo addition on mechanical properties and microstructure of grey cast iron: an overview. Mater. Today Proc. 26, 2462–2470 (2020)
M.X. Zhang, J.C. Pang, Y. Qiu et al., Influence of microstructure on the thermo-mechanical fatigue behavior and life of vermicular graphite cast irons. Mater. Sci. Eng., A 771, 138617 (2020)
E.O. Ezugwu, Z.M. Wang, Titanium alloys and their machinability—a review. J. Mater. Process. Technol. 68(3), 262–274 (1997)
D.Y. Li, D.Q. Shi, L. Feng et al., A new method of fast measuring surface tension of melt cast iron and its application in graphite shape identification. China Foundry 2, 34–37 (2005)
J. Teague, V. Richards, Age strengthening of cast irons: review of research and literature. Inter Metalcast. 4, 45–57 (2010). https://doi.org/10.1007/BF03355465
G.K. Ahiale, W.D. Choi, Y. Suh et al., Effects of MC-Type carbide forming and graphitizing elements on thermal fatigue behavior of indefinite chilled cast iron rolls. Metall. Mater. Trans. A. 46(11), 4819–4827 (2015)
J.Z. Ren, Z.L. Li, Y. Xiong et al., Effect of microstructure and mechanical properties on cutting force of different cast irons with similar tensile strength. China Foundry 16(3), 177–183 (2019)
Wu.X.Q.C.W. Yunsheng, Influence of phosphorus on hot deformation microstructure of a Ni-Fe-Cr based alloy. Mater. Sci. Eng., A 768, 138454 (2019)
B. Spa, B. Fza, A. Ns et al., The effect of niobium addition on the microstructure and properties of cast iron used in cylinder head. J. Market. Res. 9(2), 1509–1518 (2020)
Acknowledgements
The authors gratefully acknowledge support from the Jiangsu Innovation and Entrepreneurship Team Foundation, the National Natural Science Foundation of China (51825401) and the Natural Science Foundation of Heilongjiang Province of China (LH2020E032).
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Li, Yl., Wang, Q., Chen, Rr. et al. Influence of V Content on Microstructure and Mechanical Properties of Gray Cast Iron for Super-Large Cylinder Liner. Inter Metalcast 17, 1806–1814 (2023). https://doi.org/10.1007/s40962-022-00894-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40962-022-00894-7