Abstract
Depth-sensing indentation measurements of surfaces and structures with indentation depths less than 100 nm necessitate the use of accurate area functions for correct property evaluation. Here, the effect of a blunt nanoindenter tip geometry is characterized using atomic force microscopy to measure the direct tip geometry and modeled by a power law profile shape. Direct measurement of tip geometry is a method to observe changes in the tip curvature and transition from the blunt tip region to an ideal tip geometry. The tip shape, curvature, and transition to ideal geometry is found to correspond with the increase in hardness observed experimentally in SiO2 using a self-similar contact model. For a Berkovich indenter, tip bluntness was found to have a power law degree of 1.5 near the tip apex with a continuously varying degree of bluntness until an ideal pyramidal shape was reached at a depth of 160 nm.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Tabor, D., “A Simple Theory of Static and Dynamic Hardness,” Proceedings of the Royal Society of London A, Vol. 192, No. 1029, pp. 247–274, 1948.
Ternovskii, A. P., Alekhin, V. P., Shorshorov, M. Kh., Krushchov, M. M. and Skvortsov, V. N., “Micromechanical Testing of Materials by Depression,” Zavodskaya Laboratoriya, Vol. 39, No. 10, pp. 1242–1247, 1973.
Bulychev, S. I., Alekhin, V. P., Shorshorov, M. Kh., Ternovskii, A. P. and Shnyrev, G. D., “Determination of Young’s Modulus According to Indentation Diagram,” Zavodskaya Laboratoriya, Vol. 41, No. 9, pp. 1137–1140, 1975.
Sneddon, I. N., “The Relation between Load and Penetration in the Axisymmetric Boussinesq Problem for a Punch of Arbitrary Profile,” International Journal of Engineering Science, Vol. 3, No. 1, pp. 47–57, 1965.
Pharr, G. M., Oliver, W. C. and Brotzen, F. R., “On the Generality of the Relationship between Contact Stiffness, Contact Area, and Elastic Modulus during Indentation,” Journal of Materials Research, Vol. 7, No. 3, pp. 613–617, 1992.
Pethicai, J. B., Hutchings, R. and Oliver, W. C., “Hardness Measurement at Penetration Depths as Small as 20nm,” Philosophical Magazine A, Vol. 48, No. 4, pp. 593–606, 1983.
Loubet, J. L., Georges, J. M., Marchesini, J. M. and Meille, G., “Vickers Indentation Curves of Magnesium Oxide (MgO),” ASME Journal of Tribology, Vol. 106, No. 1, pp. 43–48, 1984.
Doerner, M. F. and Nix, W. D., “A Method for Interpreting the Data from Depth-sensing Indentation Instruments,” Journal of Materials Research, Vol. 1, No. 4, pp. 601–609, 1986.
Oliver, W. C. and Pharr, G. M., “An Improved Technique for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments,” Journal of Materials Research, Vol. 7, No. 6, pp. 1564–1583, 1992.
Constantinides, G., Silva, E. C. C. M., Blackman, G. S. and Van Vliet, K. J., “Dealing with Imperfection: Quantifying Potential Length Scale Artefacts from Nominally Spherical Indenter Probes,” Nanotechnology, Vol. 18, No. 30, pp. 1–14, 2007.
Ozcan, S., Farhang, K. and Filip, P., “Assessment and Verification of a Novel Method for Near Surface Measurement of Mechanical Properties,” ASME Journal of Tribology, Vol. 129, No. 2, pp. 314–320, 2007.
McMinis, J., Crombez, R., Montalvo, E. and Shen, W., “Determination of the Cross-sectional Area of the Indenter in Nano-indentation Tests,” Physica B, Vol. 391, No. 1, pp. 118–123, 2007.
Herrmann, K., Jennett, N. M., Wegener, W., Meneve, J., Hasche, K. and Seemann, R., “Progress in Determination of the Area Function of Indenters Used for Nanoindentation,” Thin Solid Films, Vol. 377–378, pp. 394–400, 2000.
Antunes, J. M., Cavaleiro, A., Menezes, L. F., Simoes, M. I. and Fernandes, J. V., “Ultra-microhardness Testing Procedure with Vickers Indenter,” Surface and Coatings Technology, Vol. 149, No. 1, pp. 27–35, 2002.
VanLandingham, M. R., Juliano, T. F. and Hagon, M. J., “Measuring Tip Shape for Instrumented Indentation Using Atomic Force Microscopy,” Measurement Science and Technology, Vol. 16, No. 11, pp. 2173–2185, 2005.
Lee, J. H., Lee, H. and Kim, D. H., “A Numerical Approach to Evaluation of Elastic Modulus Using Conical Indenter with Finite Tip Radius,” Journal of Materials Research, Vol. 23, No. 9, pp. 2528–2537, 2008.
Galanov, B. A., “Approximate Solution to Some Problems to Elastic Contact of Two Bodies,” Mechanics of Solids, Vol. 16, No. 5, pp. 61–67, 1981.
Borodich, F. M., “Similarity in the Problem of Contact between Elastic Bodies,” J. Appl. Math. Mech., Vol. 47, No. 3, pp. 519–521, 1983.
Borodich, F. M., Keer, L. M. and Korach, C. S., “Analytical Study of Fundamental Nanoindentation Test Relations for Indenters of Non-ideal Shapes,” Nanotechnology, Vol. 14, No. 7, pp. 803–808, 2003.
Galin, L. A., “Contact Problems in the Theory of Elasticity,” (Moscow, Leningrad: Gostekhizdat) English translation 1961 Sneddon, I. N. (ed.) North Carolina State College, 1953.
Bulychev, S. I., Alekhin, V. P., Shorshorov, M. Kh. and Ternovskii, A. P., “Mechanical Properties of Materials Studied from Kinetic Diagrams of Load Versus Depth of Impression During Microimpression,” Strength of Materials, Vol. 8, No. 9, pp. 1084–1089, 1976.
Williams, J. A., “Engineering Tribology,” Cambridge, 2005.
Ikezawa, K. and Maruyama, T., “Sharp Tip Geometry and Its Effect on Hardness in Nanoindentation Experiments,” Journal of Applied Physics, Vol. 91, No. 12, pp. 9689–9695, 2002.
Hou, X. D., Bushby, A. J. and Jennett, N. M., “Study of the Interaction Between the Indentation Size Effect and Hall-Petch Effect with Spherical Indenters on Annealed Polycrystalline Copper,” Journal of Physics D: Applied Physics, Vol. 41, No. 7, pp. 1–7, 2008.
Wolf, B., “Inference of Mechanical Properties from Instrumented Depth Sensing Indentation at Tiny Loads and Indentation Depths,” Crystal Research Technology, Vol. 35, No. 4, pp. 377–399, 2000.
Lim, Y. Y. and Chaudhri, M. M., “Indentation of Elastic Solids with a Rigid Vickers Pyramidal Indenter,” Mechanics of Materials, Vol. 38, No. 12, pp. 1213–1228, 2006.
Thurn, J. and Cook, R. F., “Simplified area function for sharp indenter tips in depth-sensing indentation,” Journal of Materials Research, Vol. 17, No. 5, pp. 1143–1146, 2002.
Knapp, J. A., Follstaedt, D. M., Myers, S. M., Barbour, J. C. and Friedmann, T. A., “Finite-element Modeling of Nanoindentation,” Journal of Applied Physics, Vol. 85, No. 3, pp. 1460–1474, 1999.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Choi, J.H., Korach, C.S. Tip bluntness transition measured with atomic force microscopy and the effect on hardness variation with depth in silicon dioxide nanoindentation. Int. J. Precis. Eng. Manuf. 12, 345–354 (2011). https://doi.org/10.1007/s12541-011-0045-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-011-0045-4