Abstract
Exotic materials play a key role in high-end applications. Thus, Wire Electric Discharge Machining (WEDM) stands out due to superior surface roughness and high precision. Currently, WEDM is found in rigid bed-based CNC machines constraining the workpieces in geometry and size. Parallelly, the stochastic nature of WEDM and the lack of complete mathematical models make it complex to control. As a result, whenever the servo feed becomes faster than the material removal rate, short circuits and wire break occur. On the other hand, traditional machining using six-axis industrial robots (IR) have been extensively investigated for cost efficiency, improved envelope and virtually unlimited axis combination. However, the IR design offers low stiffness, facing severe vibrations in machining hard-to-cut materials, resulting in low accuracy, poor finishing, and lack of repeatability. Thus, IRs are not comparable to CNC. The present research reviews the ideal servo control strategies for a synergistic combination of a novel machining technic of WEDM working with an IR as the servo. Employing a theoretical analysis followed by a series of simulations, it is demonstrated how the combination can be successfully controlled by frequency modulation, delivering a robotic process able to machine any hard-to-cut conductive material yet free of vibration.
Similar content being viewed by others
References
Rahul AK, Datta S, Biswal BB, Mahapatra SS (2017) Machining performance optimization for electro-discharge machining of Inconel 601, 625, 718 and 825: an integrated optimization route combining satisfaction function, fuzzy inference system and Taguchi approach. J Braz Soc Mech Sci Eng 39(9):3499–3527. https://doi.org/10.1007/s40430-016-0659-7
Chuangwen X, Jianming D, Yuzhen C, Huaiyuan L, Zhicheng S, Jing X (2018) The relationships between cutting parameters, tool wear, cutting force and vibration. Adv Mech Eng 10(1):1687814017750434. https://doi.org/10.1177/1687814017750434
Wu Q, Xie D-J, Si Y, Zhang Y-D, Li L, Zhao Y-X (2018) Simulation analysis and experimental study of milling surface residual stress of Ti-10V-2Fe-3Al. J Manuf Process 32:530–537. https://doi.org/10.1016/j.jmapro.2018.03.015
Moussaoui K, Mousseigne M, Senatore J, Chieragatti R (2015) The effect of roughness and residual stresses on fatigue life time of an alloy of titanium. Int J Adv Manuf Technol 78(1):557–563. https://doi.org/10.1007/s00170-014-6596-7
Huang JT, Liao YS (2003) Optimization of machining parameters of Wire-EDM based on Grey relational and statistical analyses. Int J Prod Res 41(8):1707–1720. https://doi.org/10.1080/1352816031000074973
Bhattacharyya GKSBP (2017) Electrical Discharge Micro-hole Machining Process of Ti–6Al–4V: Improvement of Accuracy and Performance. In: Kibria G, Bhattacharyya B, Davim J (eds) Non-traditional micromachining processes. Materials forming, machining and tribology. Springer. https://doi.org/10.1007/978-3-319-52009-4_3
Konig W (1991) Sparks machine ceramics. Powder Metall Int 23(2):96–100
Nani V-M (2017) Complex phenomena study in dielectric fluid from gap during the W-EDM processing in ultrasonic field. Int J Adv Manuf Technol 92(1–4):197–215. https://doi.org/10.1007/s00170-017-0114-7
Czelusniak T, Higa CF, Torres RD, Laurindo CAH, de Paiva Júnior JMF, Lohrengel A, Amorim FL (2018) Materials used for sinking EDM electrodes: a review. J Braz Soc Mech Sci Eng 41(1):14. https://doi.org/10.1007/s40430-018-1520-y
Zhang GZHZ (2019) Study on the effect of three dimensional wire vibration on WEDM based on a novel thermophysical model. Int J Adv Manuf Technol 100(5–8):2089–2101. https://doi.org/10.1007/s00170-018-2796-x
Das M, Dixit US (2018) Advanced machining processes. In: Davim J (ed) Introduction to mechanical engineering. Materials forming, machining and tribology. Springer. https://doi.org/10.1007/978-3-319-78488-5_9
Dave HK, Mathai VJ, Mayanak MK, Raval HK, Desai KP (2016) Study on effect of process parameters on overcut and tool wear rate during micro-electro-discharge slotting process. Int J Adv Manuf Technol 85(9):2049–2060. https://doi.org/10.1007/s00170-015-7594-0
Gjeldum N, Bilic B, Veza I (2015) Investigation and modelling of process parameters and workpiece dimensions influence on material removal rate in CWEDT process. Int J Comput Integr Manuf 28(7):715–728. https://doi.org/10.1080/0951192x.2014.900868
Ciwen H, Jinsheng Z, Jianyong L (2018) Ultra-long wire reciprocated-WEDM with dual tensile reels winded. Procedia CIRP 68:115–119. https://doi.org/10.1016/j.procir.2017.12.046
Kumar S, Mitra B, Dhanabalan S (2018) The state of art: revolutionary 5-axis CNC wire EDM and its recent developments. Int J Manag IT Eng 8(6):328–353
Kinoshita N, Fukui M, Gamo G (1982) Control of Wire-EDM preventing electrode from breaking. CIRP Ann 31(1):111–114. https://doi.org/10.1016/S0007-8506(07)63279-X
Mitsubish FA Series (2020) Wire-cut EDM FA advance series. FA Series. Tokio, Japan
Mohammad AEK, Wang D (2015) A novel mechatronics design of an electrochemical mechanical end-effector for robotic-based surface polishing. In: 2015 IEEE/SICE International Symposium on System Integration (SII). IEEE, pp 127–133
Petko M, Gac K, Góra G, Karpiel G, Ochoński J, Kobus K (2016) CNC system of the 5-axis hybrid robot for milling. Mechatronics 37(Supplement C):89–99. https://doi.org/10.1016/j.mechatronics.2016.03.001
Khalick Mohammad AE, Hong J, Wang D (2017) Polishing of uneven surfaces using industrial robots based on neural network and genetic algorithm. Int J Adv Manuf Technol 93(1–4):1463–1471. https://doi.org/10.1007/s00170-017-0524-6
Jovanovic M, Rakovic M, Tepavcevic B, Borovac B, Nikolic M (2017) Robotic fabrication of freeform foam structures with quadrilateral and puzzle shaped panels. Autom Constr 74(Supplement C):28–38. https://doi.org/10.1016/j.autcon.2016.11.003
Song YX, Liang W, Yang Y (2012) A method for grinding removal control of a robot belt grinding system. J Intell Manuf 23(5):1903–1913. https://doi.org/10.1007/s10845-011-0508-6
Song HC, Song JB (2013) Precision robotic deburring based on force control for arbitrarily shaped workpiece using CAD model matching. Int J Precis Eng Manuf 14(1):85–91. https://doi.org/10.1007/s12541-013-0013-2
Ji W, Wang LH (2019) Industrial robotic machining: a review. Int J Adv Manuf Technol 103(1–4):1239–1255. https://doi.org/10.1007/s00170-019-03403-z
Jonsson M, Stolt A, Robertsson A, von Gegerfelt S, Nilsson K (2013) On force control for assembly and deburring of castings. Prod Eng Res Devel 7(4):351–360. https://doi.org/10.1007/s11740-013-0459-1
Schneider U, Ansaloni M, Drust M, Leali F, Verl A (2013) Experimental investigation of sources of error in robot machining. In: Robotics in smart manufacturing. Springer, Berlin Heidelberg, pp 14–26
Leali F, Pellicciari M, Pini F, Berselli G, Vergnano A (2013) An offline programming method for the robotic deburring of aerospace components. In: Robotics in smart manufacturing. Springer Berlin Heidelberg, pp 1–13
Søndergaard A, Feringa J, Stan F, Maier D (2018) Robotic abrasive wire cutting of polymerized styrene formwork systems for cost-effective realization of topology-optimized concrete structures. Constr Robot 2(1–4):81–92. https://doi.org/10.1007/s41693-018-0016-8
Mao Y, Zhao H, Zhao X, Ding H (2017) Trajectory and force generation with multi-constraints for robotic belt grinding. In: Intelligent robotics and applications. Springer, Cham, pp 14–23
Lin Y, Zhao H, Ding H (2017) Posture optimization methodology of 6R industrial robots for machining using performance evaluation indexes. Robot Comput Integr Manuf 48:59–72. https://doi.org/10.1016/j.rcim.2017.02.002
Xie H, Li W, Yin Z (2018) Posture optimization based on both joint parameter error and stiffness for robotic milling. In: Intelligent robotics and applications. Springer International Publishing, Cham, pp 277–286
Ding Y, Min X, Fu W, Liang Z (2018) Research and application on force control of industrial robot polishing concave curved surfaces. Proc Inst Mech Eng Part B J Eng Manuf 233(6):1674–1686. https://doi.org/10.1177/0954405418802309
Domroes F, Krewet C, Kuhlenkoetter BJMME (2013) Application and analysis of force control strategies to deburring and grinding. Mod Mech Eng 3(02):11
Chen F, Zhao H, Li DW, Chen L, Tan C, Ding H (2019) Robotic grinding of a blisk with two degrees of freedom contact force control. Int J Adv Manuf Technol 101(1–4):461–474. https://doi.org/10.1007/s00170-018-2925-6
Diao S, Chen X, Luo J (2018) Development and experimental evaluation of a 3D vision system for grinding robot. Sensors (Basel) 18(9):3078. https://doi.org/10.3390/s18093078
Zhang G, Li H, Zhang Z, Ming W, Wang N, Huang Y (2016) Vibration modeling and analysis of wire during the WEDM process. Mach Sci Technol 20(2):173–186. https://doi.org/10.1080/10910344.2015.1085312
Sarkar ASS (2019) Influence of different control strategies in wire electrical discharge machining of varying height job. Int J Adv Manuf Technol 100(5–8):1299–1309. https://doi.org/10.1007/s00170-016-9045-y
Yan M-T (2010) An adaptive control system with self-organizing fuzzy sliding mode control strategy for micro wire-EDM machines. Int J Adv Manuf Technol 50(1):315–328. https://doi.org/10.1007/s00170-009-2481-1
Rajurkar KP, Wang WM, Lindsay RP (1991) On-line monitor and control for wire breakage in WEDM. CIRP Ann 40(1):219–222. https://doi.org/10.1016/S0007-8506(07)61972-6
Rajurkar KP, Wang WM, McGeough JA (1994) WEDM identification and adaptive control for variable-height components. CIRP Ann 43(1):199–202. https://doi.org/10.1016/S0007-8506(07)62195-7
Rajurkar KP, Wang WM, Zhao WS (1997) WEDM-adaptive control with a multiple input model for indentification of workpiece height. CIRP Ann 46(1):147–150. https://doi.org/10.1016/S0007-8506(07)60795-1
Yan MT, Liao YS (1998) Adaptive control of the WEDM process using the fuzzy control strategy. J Manuf Syst 17(4):263–274. https://doi.org/10.1016/S0278-6125(98)80074-5
Yan MT, Li HP, Liang JF (1999) The application of fuzzy control strategy in servo feed control of wire electrical discharge machining. Int J Adv Manuf Technol 15(11):780–784. https://doi.org/10.1007/s001700050131
Liao YS, Woo JC (2000) Design of a fuzzy controller for the adaptive control of WEDM process. Int J Mach Tools Manuf 40(15):2293–2307. https://doi.org/10.1016/S0890-6955(00)00036-5
Yan MT, Liao YS, Chang CC (2001) On-line estimation of workpiece height by using neural networks and hierarchical adaptive control of WEDM. Int J Adv Manuf Technol 18(12):884–891. https://doi.org/10.1007/PL00003956
Liao YS, Chuang TJ, Yu YP (2013) On-line workpiece height estimation and its application in servo feed control of WEDM process. Procedia CIRP 6:226–231. https://doi.org/10.1016/j.procir.2013.03.050
Han F, Wachi S, Kunieda M (2004) Improvement of machining characteristics of micro-EDM using transistor type isopulse generator and servo feed control. Precis Eng 28(4):378–385. https://doi.org/10.1016/j.precisioneng.2003.11.005
Liao YS, Yu YP (2004) Study of specific discharge energy in WEDM and its application. Int J Mach Tools Manuf 44(12):1373–1380. https://doi.org/10.1016/j.ijmachtools.2004.04.008
Yan M-T, Chien H-T (2007) Monitoring and control of the micro wire-EDM process. Int J Mach Tools Manuf 47(1):148–157. https://doi.org/10.1016/j.ijmachtools.2006.02.006
Dekeyser W, Snoeys R, Jennes M (1988) Expert system for wire cutting EDM, based on pulse classification and thermal modeling. Robot Comput Integr Manuf 4(1):219–224. https://doi.org/10.1016/0736-5845(88)90080-4
Lee WM, Liao YS (2007) Adaptive control of the WEDM process using a self-tuning fuzzy logic algorithm with grey prediction. Int J Adv Manuf Technol 34(5):527–537. https://doi.org/10.1007/s00170-006-0623-2
Ishibashi Y, Komori A (1994) Wire electric discharge machine having alterable discharge period
Yang KTH-H (2015) A new approach for Micro-WEDM control based on Real-Time estimation of material removal rate. Int J Precis Eng Manuf 16(2):241–246. https://doi.org/10.1007/s12541-015-0032-2
Zhidong L, Haoran C, Huijun P, Mingbo Q, Zongjun T (2015) Automatic control of WEDM servo for silicon processing using current pulse probability detection. Int J Adv Manuf Technol 76(1–4):367–374. https://doi.org/10.1007/s00170-014-6252-2
Trung Kien H (2017) Development of a WEDM system with high machining efficiency. In: 2017 international conference on system science and engineering (ICSSE), 21–23 July 2017, pp 397–399. https://doi.org/10.1109/ICSSE.2017.8030904
Huang G, Xia W, Qin L, Zhao W (2018) Online workpiece height estimation for reciprocated traveling wire EDM based on support vector machine. Procedia CIRP 68:126–131. https://doi.org/10.1016/j.procir.2017.12.034
Li C, Liu Z, Fang L, Pan H, Qiu M (2018) Super-high-thickness high-speed wire electrical discharge machining. J Adv Manuf Technol 95(5):1805–1818. https://doi.org/10.1007/s00170-017-1246-5
Zengxi P, Hui Z (2007) Analysis and suppression of chatter in robotic machining process. In: 2007 international conference on control, automation and systems, 17–20 Oct, pp 595–600. https://doi.org/10.1109/ICCAS.2007.4407093
Moradi H, Bakhtiari-Nejad F, Movahhedy MR (2008) Tuneable vibration absorber design to suppress vibrations: an application in boring manufacturing process. J Sound Vib 318(1):93–108. https://doi.org/10.1016/j.jsv.2008.04.001
Yuan L, Pan ZX, Ding DH, Sun SS, Li WH (2018) A review on chatter in robotic machining process regarding both regenerative and mode coupling mechanism. IEEE-ASME Trans Mechatron 23(5):2240–2251. https://doi.org/10.1109/Tmech.2018.2864652
Wang G, Dong H, Guo Y, Ke Y (2017) Chatter mechanism and stability analysis of robotic boring. J Int J Adv Manuf Technol 91(1):411–421. https://doi.org/10.1007/s00170-016-9731-9
Quintana G, Ciurana J (2011) Chatter in machining processes: a review. Int J Mach Tools Manuf 51(5):363–376. https://doi.org/10.1016/j.ijmachtools.2011.01.001
Zhang XJ, Xiong CH, Ding Y, Feng MJ, Lun Xiong Y (2012) Milling stability analysis with simultaneously considering the structural mode coupling effect and regenerative effect. Int J Mach Tools Manuf 53(1):127–140. https://doi.org/10.1016/j.ijmachtools.2011.10.004
Gasparetto A (1998) A system theory approach to mode coupling chatter in machining. J Dyn Syst Meas Contr 120(4):545–547. https://doi.org/10.1115/1.2801501
Pan ZX, Zhang H, Zhu ZQ, Wang JJ (2006) Chatter analysis of robotic machining process. J Mater Process Technol 173(3):301–309. https://doi.org/10.1016/j.jmatprotec.2005.11.033
Wang Z, Keogh P (2017) Active vibration control for robotic machining. In: ASME 2017 International mechanical engineering congress and exposition, V002T02A079. https://doi.org/10.1115/imece2017-71670
Chen Z, Huang Y, Huang H, Zhang Z, Zhang G (2015) Three-dimensional characteristics analysis of the wire-tool vibration considering spatial temperature field and electromagnetic field in WEDM. Int J Mach Tools Manuf 92:85–96. https://doi.org/10.1016/j.ijmachtools.2015.03.003
Kamei T, Okada A, Okamoto Y (2016) High-speed observation of thin wire movement in fine wire EDM. Procedia CIRP 42:596–600. https://doi.org/10.1016/j.procir.2016.02.266
Mingqi L, Minghui L, Guangyao X (2005) Study on the variations of form and position of the wire electrode in WEDM-HS. Int J Adv Manuf Technol 25(9):929–934. https://doi.org/10.1007/s00170-003-1915-4
ABB-IRB120 (2020) ABB’s smallest robot—for flexible and compact. Document ID: 3HAC035960-001—revision Q. Zurich, Switzerland
CATIA V5-6 (2020) CATIA V5-6. Vélizy-Villacoublay, France
ANSYS R19 (2020) ANSYS R19—Finite Element Analysis (FEA) Software. R19. Canonsburg, Pennsylvania, USA
Funding
Lately, no funding was received for conducting this study.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
All the authors declare that they have no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Almeida, S.T., Mo, J.P.T., Bil, C. et al. Servo Control Strategies for Vibration-Control in Robotic Wire EDM Machining. Arch Computat Methods Eng 29, 113–127 (2022). https://doi.org/10.1007/s11831-021-09570-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11831-021-09570-1