Abstract
An effect of the friction stir processing (FSP), its pass numbers and addition of the SiO2 nanoparticles on microhardness, wear behavior and corrosion performance of the Al6061 aluminum alloy was investigated. Scanning electron microscopy (SEM) and optical microscopy were utilized to characterize the microstructure of the alloy, FSPed and composite samples. SEM observations revealed that the SiO2 particles were not uniformly dispersed in the matrix after two passes of FSP. However, increasing the pass number more than two passes resulted in a great improvement in the distribution of the SiO2 particles. The application of FSP led to overall softening compared to the base metal. Softening of the Al6061 alloy was probably attributed to the coarsening of Mg2Si. Corrosion resistance of the FSPed samples found a significant reduction compared to the base metal. Applying higher pass number of the process and also addition of the SiO2 nanoparticles improved the wear behavior of the samples.
Similar content being viewed by others
References
I.J. Polmear, D.S. John, J.F. Nie, and M. Qian, Light alloys: metallurgy of the light metals, 5th ed., Elsevier Ltd, Amsterdam, 2017
F.C. Campbell, Manufacturing Technology for Aerospace Structural Materials (2006). https://doi.org/10.1016/b978-185617495-4/50002-0.
D. Aruri, K. Adepu, K. Adepu, and K. Bazavada, Wear and Mechanical Properties of 6061-T6 Aluminum Alloy Surface Hybrid Composites [(SiC + Gr) and (SiC + Al2O3)] Fabricated by Friction Stir Processing, J. Mater. Res. Technol., 2013, 2, p 362–369. https://doi.org/10.1016/j.jmrt.2013.10.004
D.B. Miracle, Metal Matrix Composites—from Science to Technological Significance, Compos. Sci. Technol., 2005, 65, p 2526–2540. https://doi.org/10.1016/j.compscitech.2005.05.027
H. Chen, W. Wang, H. Nie, J. Zhou, Y. Li, and P. Zhang, Microstructure and Mechanical Properties of B4C/6061Al Laminar Composites Fabricated by Power Metallurgy, Vacuum, 2017, 143, p 363–370. https://doi.org/10.1016/j.vacuum.2017.06.009
S. Lü, P. Xiao, D. Yuan, K. Hu, and S. Wu, Preparation of Al Matrix Nanocomposites by Diluting the Composite Granules Containing Nano-SiCp Under Ultrasonic Vibration, J. Mater. Sci. Technol., 2018, 34, p 1609–1617. https://doi.org/10.1016/j.jmst.2018.01.003
B.C. Kandpal, J. Kumar, and H. Singh, Manufacturing and Technological Challenges in Stir Casting of Metal Matrix Composites—A Review, Mater. Today Proc., 2018, 5, p 5–10. https://doi.org/10.1016/j.matpr.2017.11.046
S.M.Y. Kaku, A.K. Khanra, and M.J. Davidson, Effect of Deformation on Properties of Al/Al-alloy ZrB2 Powder Metallurgy Composite, J. Alloys Compd., 2018, 747, p 666–675. https://doi.org/10.1016/j.jallcom.2018.03.088
A.N. Attia, Surface Metal Matrix Composites, Mater. Des., 2001, 22, p 451–457. https://doi.org/10.1016/S0261-3069(00)00081-9
A. Kurt, I. Uygur, and E. Cete, Surface Modification of Aluminium by Friction Stir Processing, J. Mater. Process. Technol., 2011, 211, p 313–317. https://doi.org/10.1016/j.jmatprotec.2010.09.020
S. Dejiu, C. Jingrui, L. Guolong, H. Donglei, W. Lailei, M. Haojie, X. Yonghong, C. He, and Y. Yaqian, Effect of Ultrasonic on Microstructure and Growth Characteristics of Micro-Arc Oxidation Ceramic Coatings on 6061 Aluminum Alloy, Vacuum, 2014, 99, p 143–148. https://doi.org/10.1016/j.vacuum.2013.05.022
H.S. Arora, H. Singh, and B.K. Dhindaw, Composite Fabrication Using Friction Stir Processing—A Review, Int. J. Adv. Manuf. Technol., 2012, 61, p 1043–1055. https://doi.org/10.1007/s00170-011-3758-8
M.S. Węglowski, Friction Stir Processing—State of the Art, Arch. Civ. Mech. Eng., 2018, 18, p 114–129. https://doi.org/10.1016/j.acme.2017.06.002
S. Rathee, S. Maheshwari, and A.N. Siddiquee, Issues and Strategies in Composite Fabrication via Friction Stir Processing: A Review, Mater. Manuf. Process., 2018, 33, p 239–261. https://doi.org/10.1080/10426914.2017.1303162
S. Rathee, S. Maheshwari, A.N. Siddiquee, and M. Srivastava, Distribution of Reinforcement Particles in Surface Composite Fabrication via Friction Stir Processing: Suitable Strategy, Mater. Manuf. Process., 2018, 33, p 262–269. https://doi.org/10.1080/10426914.2017.1303147
Z. Ding, C. Zhang, L. Xie, L.-C. Zhang, L. Wang, and W. Lu, Effects of Friction Stir Processing on the Phase Transformation and Microstructure of TiO2-Compounded Ti–6Al-4V Alloy, Metall. Mater. Trans. A, 2016, https://doi.org/10.1007/s11661-016-3809-8
P. Liu, Y. Li, G. Zhang, and K. Feng, Relation Between Thermal Effect and Phase Transformation of Aluminium Matrix Surface Composite Adding Al-Based Amorphous Fabricated by FSP, Vacuum, 2016, 131, p 65–68. https://doi.org/10.1016/j.vacuum.2016.06.002
Z.Y. Ma, Friction Stir Processing Technology: A Review, Metall. Mater. Trans. A, 2008, 39, p 642–658. https://doi.org/10.1007/s11661-007-9459-0
S. Kumar, S.K. Reddy, and S.V. Joshi, Microstructure and Performance of Cold Sprayed Al–SiC Composite Coatings with High Fraction of Particulates, Surf. Coat. Technol., 2017, 318, p 62–71. https://doi.org/10.1016/j.surfcoat.2016.11.047
A. Sharma, V.M. Sharma, S. Mewar, S.K. Pal, and J. Paul, Friction Stir Processing of Al6061-SiC-Graphite Hybrid Surface Composites, Mater. Manuf. Process., 2018, 33, p 795–804. https://doi.org/10.1080/10426914.2017.1401726
M. Salehi, M. Saadatmand, and J.A. Mohandesi, Optimization of Process Parameters for Producing AA6061/SiC Nanocomposites by Friction Stir Processing, Trans. Nonferrous Met. Soc. China, 2012, 22, p 1055–1063. https://doi.org/10.1016/S1003-6326(11)61283-1
D.H. Choi, Y. Il Kim, D.U. Kim, and S.B. Jung, Effect of SiC Particles on Microstructure and Mechanical Property of Friction Stir Processed AA6061-T4, Trans. Nonferrous Met. Soc. China (Engl. Ed.), 2012, 22, p s614–s618. https://doi.org/10.1016/s1003-6326(12)61773-7
S. Rathee, S. Maheshwari, A.N. Siddiquee, M. Srivastava, and S.K. Sharma, Process Parameters Optimization for Enhanced Microhardness of AA 6061/SiC Surface Composites Fabricated via Friction Stir Processing (FSP), Mater. Today Proc., 2016, 3, p 4151–4156. https://doi.org/10.1016/j.matpr.2016.11.089
H. Zuhailawati, M.N. Halmy, I.P. Almanar, and B.K. Dhindaw, Friction Stir Processed of 6061-T6 Aluminum Alloy Reinforced with Silica from Rice Husk Ash, Adv. Mater. Res., 2014, 1024, p 227–230. https://doi.org/10.4028/www.scientific.net/AMR.1024.227
A. Devaraju, A. Kumar, and B. Kotiveerachari, Influence of Addition of Grp/Al2O3p with SiCp on Wear Properties of Aluminum alloy 6061-T6 Hybrid Composites via Friction Stir Processing, Trans. Nonferrous Met. Soc. China (Engl. Ed.), 2013, https://doi.org/10.1016/s1003-6326(13)62593-5
K. Zhao, Z.Y. Liu, B.L. Xiao, D.R. Ni, and Z.Y. Ma, Origin of Insignificant Strengthening Effect of CNTs in T6-Treated CNT/6061Al Composites, Acta Metall. Sin. (Engl. Lett.), 2018, 31, p 134–142. https://doi.org/10.1007/s40195-017-0626-z
Z.Y. Liu, B.L. Xiao, W.G. Wang, and Z.Y. Ma, Tensile Strength and Electrical Conductivity of Carbon Nanotube Reinforced Aluminum Matrix Composites Fabricated by Powder Metallurgy Combined with Friction Stir Processing, J. Mater. Sci. Technol., 2014, 30, p 649–655. https://doi.org/10.1016/j.jmst.2014.04.016
A. Devaraju, A. Kumar, and B. Kotiveerachari, Influence of Rotational Speed and Reinforcements on Wear and Mechanical Properties of Aluminum Hybrid Composites via Friction Stir processing, Mater. Des., 2013, 45, p 576–585. https://doi.org/10.1016/j.matdes.2012.09.036
D.R. Ni, J.J. Wang, Z.N. Zhou, and Z.Y. Ma, Fabrication and Mechanical Properties of Bulk NiTip/Al Composites Prepared by Friction Stir Processing, J. Alloys Compd., 2014, 586, p 368–374. https://doi.org/10.1016/j.jallcom.2013.10.013
V. Kishan, A. Devaraju, and K.P. Lakshmi, Tribological Properties of Bano TiB2 Particle Reinforced 6061-T6 Aluminum Alloy Surface Composites via Friction Stir Processing, Mater. Today Proc., 2018, 5, p 1615–1619. https://doi.org/10.1016/j.matpr.2017.11.254
V. Kishan, A. Devaraju, and K.P. Lakshmi, Influence of Volume Percentage of NanoTiB2 Particles on Tribological & Mechanical Behaviour of 6061-T6 Al Alloy Nano-surface Composite Layer Prepared via Friction Stir Process, Def. Technol., 2017, 13, p 16–21. https://doi.org/10.1016/j.dt.2016.11.002
D.C. Hofmann and K.S. Vecchio, Submerged Friction Stir Processing (SFSP): An Improved Method for Creating Ultra-Fine-Grained Bulk Materials, Mater. Sci. Eng. A, 2005, 402, p 234–241. https://doi.org/10.1016/j.msea.2005.04.032
A. Ebnonnasir, F. Karimzadeh, and M.H. Enayati, Novel Artificial Neural Network Model for Evaluating Hardness of Stir Zone of Submerge Friction Stir Processed Al 6061-T6 Plate, Mater. Sci. Technol., 2011, 27, p 990–995. https://doi.org/10.1179/174328409X425290
M.M. Jalilvand, Y. Mazaheri, A. Heidarpour, and M. Roknian, Development of A356/Al2O3 + SiO2 Surface Hybrid Nanocomposite by Friction Stir Processing, Surf. Coat. Technol., 2019, 360, p 121–132. https://doi.org/10.1016/j.surfcoat.2018.12.126
ASTM E384–17, Standard test method for microindentation hardness of materials, ASTM International, West Conshohocken, 2017
ASTM G99–17, Standard test method for wear testing with a pin-on-disk apparatus, ASTM International, West Conshohocken, 2017
T.R. McNelley, S. Swaminathan, and J.Q. Su, Recrystallization Mechanisms During Friction Stir Welding/Processing of Aluminum Alloys, Scr. Mater., 2008, 58, p 349–354. https://doi.org/10.1016/j.scriptamat.2007.09.064
F. Humphreys and M. Matherly, Recrystallization and related annealing phenomena, Elsevier Sci. Ltd Publ., New York, 1995, p 173–178
F.J. Humphreys, P.B. Prangnell, and R. Priestner, Fine-Grained Alloys by Thermomechanical Processing, Curr. Opin. Solid State Mater. Sci., 2001, 5, p 15–21. https://doi.org/10.1016/S1359-0286(00)00020-6
R.S. Mishra and Z.Y. Ma, Friction Stir Welding and Processing, Mater. Sci. Eng. R Rep., 2005, 50, p 1–78. https://doi.org/10.1016/j.mser.2005.07.001
Y. Mazaheri, F. Karimzadeh, and M.H. Enayati, Tribological Behavior of A356/Al2O3 Surface Nanocomposite Prepared by Friction Stir Processing, Metall. Mater. Trans. A, 2014, 45, p 2250–2259. https://doi.org/10.1007/s11661-013-2140-x
J.F. Guo, J. Liu, C.N. Sun, S. Maleksaeedi, G. Bi, M.J. Tan, and J. Wei, Effects of Nano-Al2O3 Particle Addition on Grain Structure Evolution and Mechanical Behaviour of Friction-Stir-Processed Al, Mater. Sci. Eng. A, 2014, 602, p 143–149. https://doi.org/10.1016/j.msea.2014.02.022
S. Ahmadifard, S. Kazemi, and A. Heidarpour, Production and Characterization of A5083-Al2O3–TiO2 Hybrid Surface Nanocomposite by Friction Stir Processing, Proc. Inst. Mech. Eng. Part L J. Mater. Des. Appl., 2018, 232, p 287–293. https://doi.org/10.1177/1464420715623977
R. Yang, Z. Zhang, Y. Zhao, G. Chen, Y. Guo, M. Liu, and J. Zhang, Materials Characterization Effect of Multi-Pass Friction Stir Processing on Microstructure and Mechanical Properties of Al3Ti/A356 Composites, Mater. Charact., 2015, 106, p 62–69. https://doi.org/10.1016/j.matchar.2015.05.019
K.-M. Lee, D.-K. Oh, W.-S. Choi, T. Weissgärber, and B. Kieback, Thermomechanical Properties of AlN–Cu Composite Materials Prepared by Solid State Processing, J. Alloys Compd., 2007, 434–435, p 375–377. https://doi.org/10.1016/j.jallcom.2006.08.176
C.Y.H. Lim, S.C. Lim, and M. Gupta, Wear Behaviour of SiCp-Reinforced Magnesium Matrix Composites, Wear, 2003, 255, p 629–637. https://doi.org/10.1016/S0043-1648(03)00121-2
M. Akbari, M.H. Shojaeefard, P. Asadi, and A. Khalkhali, Wear and Mechanical Properties of Surface Hybrid Metal Matrix Composites on Al–Si Aluminum Alloys Fabricated by Friction Stir Processing, Proc. Inst. Mech. Eng. Part L J. Mater. Des. Appl., 2017, 233, p 790–799. https://doi.org/10.1177/1464420717702413
C.J. Hsu, C.P.Y. Chang, P.W. Kao, N.J. Ho, and C.P.Y. Chang, Al-Al3Ti Nanocomposites Produced in situ by Friction Stir Processing, Acta Mater., 2006, 54, p 5241–5249. https://doi.org/10.1016/j.actamat.2006.06.054
A.G. Rao, V.A. Katkar, G. Gunasekaran, V.P. Deshmukh, N. Prabhu, and B.P. Kashyap, Effect of Multipass Friction Stir Processing on Corrosion Resistance of Hypereutectic Al-30Si Alloy, Corros. Sci., 2014, 83, p 198–208. https://doi.org/10.1016/j.corsci.2014.02.013
K. Surekha, B.S. Murty, and K.P. Rao, Microstructural Characterization and Corrosion Behavior of Multipass Friction Stir Processed AA2219 Aluminium Alloy, Surf. Coat. Technol., 2008, 202, p 4057–4068. https://doi.org/10.1016/j.surfcoat.2008.02.001
K. Surekha, B.S. Murty, and K. Prasad Rao, Comparison of Corrosion Behaviour of Friction Stir Processed and Laser Melted AA 2219 Aluminium Alloy, Mater. Des., 2011, 32, p 4502–4508. https://doi.org/10.1016/j.matdes.2011.03.033
R.A. Behnagh, M.K. Besharati Givi, and M. Akbari, Mechanical Properties, Corrosion Resistance, and Microstructural Changes During Friction Stir Processing of 5083 Aluminum Rolled Plates, Mater. Manuf. Process., 2012, 27, p 636–640. https://doi.org/10.1080/10426914.2011.593243
M. Amra, K. Ranjbar, and R. Dehmolaei, Mechanical Properties and Corrosion Behavior of CeO2 and SiC Incorporated Al5083 Alloy Surface Composites, J. Mater. Eng. Perform., 2015, 24, p 3169–3179. https://doi.org/10.1007/s11665-015-1596-9
F. Gharavi, K.A. Matori, R. Yunus, N.K. Othman, and F. Fadaeifard, Corrosion Behavior of Al6061 Alloy Weldment Produced by Friction Stir Welding Process, J. Mater. Res. Technol., 2015, 4, p 314–322. https://doi.org/10.1016/j.jmrt.2015.01.007
J.F. Flores, A. Neville, N. Kapur, and A. Gnanavelu, Corrosion and Erosion-Corrosion Processes of Metal-Matrix Composites in Slurry Conditions, J. Mater. Eng. Perform., 2012, 21, p 395–405. https://doi.org/10.1007/s11665-011-9926-z
V. Fahimpour, S.K. Sadrnezhaad, and F. Karimzadeh, Corrosion Behavior of Aluminum 6061 Alloy Joined by Friction Stir Welding and Gas Tungsten Arc Welding Methods, Mater. Des., 2012, 39, p 329–333. https://doi.org/10.1016/j.matdes.2012.02.043
D.R. Ni, B.L. Xiao, Z.Y. Ma, Y.X. Qiao, and Y.G. Zheng, Corrosion Properties of Friction-Stir Processed Cast NiAl Bronze, Corros. Sci., 2010, 52, p 1610–1617. https://doi.org/10.1016/j.corsci.2010.02.026
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Mazaheri, Y., Heidarpour, A., Jalilvand, M.M. et al. Effect of Friction Stir Processing on the Microhardness, Wear and Corrosion Behavior of Al6061 and Al6061/SiO2 Nanocomposites. J. of Materi Eng and Perform 28, 4826–4837 (2019). https://doi.org/10.1007/s11665-019-04260-3
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-019-04260-3