A problem of an edge crack with a fracture process zone in semi-infinite orthotropic planes under the pure- and mixed-mode loading (I and II modes) was studied. A cohesive zone with different cohesive lengths in opening and sliding modes (multiple cohesive zone) was used to simulate the fracture process zone. The smooth crack closure condition defines cohesive lengths of the two fracture modes. The problem of an edge crack that is normal to the plate edge was formulated in terms of integral equations for the unknown displacement discontinuity along the crack. A collocation method applied to two singular integral equations with Cauchy kernel gave the equations for critical loads and respective discrete cohesive tractions and separations. These equations are non-linear since a dependence of cohesive tractions on crack opening was taken according to potential-based traction–separation law. An iterative procedure was used to satisfy the condition of smooth crack closure. A generalization of the potential, well-known in the literature, was used to generate the cohesive traction field. The potential combines pure-mode laws without mode-mixity parameters. Two types of generalized potential functions were considered, and a critical analysis was carried out. Numerical solutions were presented for the cohesive tractions and separations in critical state when both pure-mode cohesive laws were trapezoidal shaped. Comparison of the fracture loci obtained for two types of generalized potentials allowed us to conclude that the type strongly influences the critical state parameters.
Similar content being viewed by others
References
J. P. Clech, L. M. Keer and J. L. Lewis, “A model of tension and compression cracks with cohesive zone at a bonecement interface,” ASME. J. Biomech. Eng., 107, No. 2, 175-182 (1985).
H. Altenbach, V. M. Nazarenko and V. L. Bogdanov, “Influence of initial stress on fracture of a halfspace containing a penny-shaped crack under radial shear,” Int. J. Fract., 104, 275-289 (2000).
V. L. Bogdanov, “On a circular shear crack in a semi-infinite composite with initial stresses,” Mat. Sci., 43, No. 3, 321-330 (2007).
V. L. Bogdanov and V. M. Nazarenko, “Study of the compressive failure of a semi-infinite elastic material with a harmonic potential,” Int. Appl. Mech., 30, No. 10, 760-765 (1994).
V. L. Bogdanov, “Influence of initial stresses on fracture of composite materials containing interacting cracks,” J. Math. Sci., 165, No. 3, 371-384 (2010).
V. L. Bogdanov, A. N. Guz and V. M. Nazarenko, “Stress–strain state of a material under forces acting along a periodic set of coaxial mode II penny-shaped cracks,” Int. Appl. Mech., 47, No. 12, 1339-1350 (2011).
V. L. Bogdanov, “Influence of initial stresses on the stressed state of a composite with a periodic system of parallel coaxial normal tensile cracks,” J. Math. Sci., 186, No. 1, 1-13 (2012).
V. L. Bogdanov, A. N. Guz and V. M. Nazarenko, “Nonclassical problems in the fracture mechanics of composites with interacting cracks,” Int. Appl. Mech., 51, No. 1, 64-84 (2015).
O. Bowie and P. Tracy, “On the solution of the Dugdale model,” Eng. Fract. Mech., 10, 249-256 (1978).
I. Howard and N. Otter, “On the elastic–plastic deformation of a sheet containing an edge crack,” J. Mech. Phys. Solids., 23, 139-149 (1975).
H. Petroski, “Dugdale plastic zone sizes for edge cracks,” Int. J. Fract., 15, No. 3, 217-230 (1979).
V. D. Kuliev, “Plastic deformation at the tip of an edge crack,” J. Appl. Math. Mech., 43, 171-178 (1979).
B. M. Singh, H. T. Danyluk and J. Vrbik, “A note on plastic deformation at the tip of an edge crack,” Acta Mech., 55, 81-86 (1985).
D. S. Dugdale, “Yielding of steel sheets containing slits,” J. Mech. Phys. Solids, 8, 100-104 (1960).
G. I. Barenblatt, “The mathematical theory of equilibrium cracks in brittle fracture,” Adv. Appl. Mech., 7, 55-129 (1962).
A. Hillerborg, M. Modeer and P. E. Petersson, “Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements,” Cem. Concr. Res., 6, 773-781 (1976).
H. Ferdjani and R. Abdelmoula, “Propagation of a Dugdale crack at the edge of a half plane,” Continuum Mech. Thermodyn., 30, 195-205 (2018).
S. Wang and J. P. Dempsey, “A cohesive edge crack,” Eng. Fract. Mech., 78, 1353-1373 (2011).
L. T. Thanh, L. A. Belaya and I. M. Lavit, J. Phys.: Conf. Ser. 973, 012020 (2018).
M. Selivanov, “An edge crack with cohesive zone [in Ukrainian],” Dopov. Nac. akad. Nauk Ukr., No. 3, 46-54 (2019).
M. Selivanov, “Solving a problem on an edge crack with cohesive zone by the regularization of a singular integral equation [in Ukrainian],” Dopov. Nac. akad. Nauk Ukr, No. 5, 34-43 (2019).
M. Selivanov, “An edge crack with cohesive zone in orthotropic body [in Ukrainian],” Dopov. Nac. akad. nauk Ukr., No. 6, 25-34 (2019).
A. Needleman, “A continuum model for void nucleation by inclusion debonding,” J. Appl. Mech., 54, 525-531 (1987).
C. Y. Hui et al., “Cohesive zone models and fracture,” J. Adhesion, 87, 1-52 (2011).
K. Park, G. H. Paulino and J. R. Roesler, “A unified potential-based cohesive model of mixed-mode fracture,” J. Mech. Phys. Solids, 57, No. 6, 891-908 (2009).
K. Park and G. H. Paulino, “Cohesive zone models: A critical review of traction–separation relationships across fracture surfaces,” Appl. Mech. Reviews, 64, No. 6, 060802–20 (2013).
M. Selivanov, “Subcritical and critical states of a crack with failure zones,” Appl. Math. Model., 72, 104-128 (2019).
M. Selivanov and Y. Chornoivan, “A semi-analytical solution method for problems of cohesive fracture and some of its applications,” Int. J. Fract., 212, No. 1, 113-121 (2018).
M. Selivanov, Y. Chornoivan and O. Kononchuk, “Determination of crack opening displacement and critical load parameter within a cohesive zone model,” Continuum Mech. Thermodyn., 31, No. 2, 569-586 (2018).
Z. H. Jin and C. T. Sun, “Cohesive zone modeling of interface fracture in elastic bi-materials,” Eng. Fract. Mech., 72, 1805-1817 (2005).
J. Sweeney, “The stress intensity for an edge crack in a semi-infinite orthotropic body,” Int. J. Fract., 37, 233-241 (1988).
Z. Suo, “Delamination specimens for orthotropic materials,” J. Appl. Mech., 57, 627-634 (1990).
K. B. Broberg, Cracks and Fracture. Academic Press, London (1999).
F. Erdogan, G. D. Gupta and T. S. Cook, “Numerical solution of singular integral equations,” in: G. C. Sih (eds.) Methods of analysis and solutions of crack problems. Mechanics of Fracture, 1, Springer, Dordrecht (1973), pp. 368-425.
A. Kaminsky, M. Selivanov and Y. Chornoivan, “Cohesive zone length influence on the critical load for a body with mode I crack [in Ukrainian],” Dopov. Nac. akad. nauk Ukr., No. 8., 36-44 (2018).
M. P. Savruk, E. Madenci and S. Shkarayev, “Singular integral equations of the second kind with generalized Cauchytype kernels and variable coefficients,” Int. J. Numer. Meth. Eng., 45, 1457-1470 (1999).
M. Selivanov, “Quasi-static problems of fracture mechanics for elastic and viscoelastic bodies in the framework of cohesive zone models [in Ukrainian],” Dr. Sci. Thesis. S.P. Timoshenko Institute of Mechanics, National Academy of Sciences Ukraine, Kyiv (2017).
F. P. Gerstle, “Composites”. In: Encyclopedia of Polymer Science and Engineering. Wiley, New York (1991).
C. Zweben, “Composite materials”. In: Mechanical Engineers’ Handbook. Ed. by M. Kutz. 4th ed. John Wiley & Sons, Inc. (2015).
R. Dimitri et al., “A consistency assessment of coupled cohesive zone models for mixed-mode debonding problems,” Frattura ed Integrità Strutturale, 46, 266-283 (2014).
M. Selivanov, L. Nazarenko, and H. Altenbach, “Modeling the slow crack growth of an edge crack within the cohesive zone model approach”. in: I. Giorgio et al. (eds.) Theoretical Analyses, Computations, and Experiments of Multiscale Materials: A Tribute to Francesco dell’Isola, pp. 505-535, Advanced Structured Materials, vol. 175, Springer International Publishing, Cham, (2022).
A. Kaminsky and M. Selivanov, “Modeling subcritical crack growth in a viscoelastic body under concentrated forces,”Int. Appl. Mech., 53, No. 4, 538-544 (2017).
H. Stang et al. “On the application of cohesive crack modeling in cementitious materials,” Mater. Struct., 40, 365-374 (2007).
A. Kaminsky and E. Kurchakov, “Fracture process zone at the tip of a mode I crack in a nonlinear elastic orthotropic material,” Int. Appl. Mech., 55, No. 1, 23-40 (2019).
D. Engwirda, “Locally-optimal Delaunay-refinement and optimisation-based mesh generation,” Ph.D. Thesis. School of Mathematics and Statistics, Univ. of Sydney (2014).
D. Engwirda and D. Ivers, “Off-centre Steiner points for Delaunay-refinement on curved surfaces,” Computer-Aided Design, 72, 157-171 (2016).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Selivanov, M., Bogdanov, V. & Altenbach, H. Solving Some Problems of Crack Mechanics for a Normal Edge Crack in Orthotropic Solid Within the Cohesive Zone Model Approach. Mech Compos Mater 59, 335–362 (2023). https://doi.org/10.1007/s11029-023-10099-6
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11029-023-10099-6