Abstract
The feasibility of reprocessing has been investigated as a possible alternative for acrylonitrile–butadiene–styrene terpolymer (ABS) recycling. Up to 10 reprocessing cycles have been performed by both extrusion and injection techniques and their effect on thermal and mechanical properties have been studied. Moreover, the effect of the combined reprocessing and accelerated weathering has been analyzed. Measurements collected after each molding cycle indicated virtually complete retention of thermal properties. The same behaviour has been observed from accelerated weathering tests. With respect to the mechanical properties, neither the flow index nor the tensile strength were affected by the number of reprocessing cycles though the impact strength decreased slightly. However, the studies based on the accelerated weathering show that there is an important influence of the number of reprocessing cycles on the tensile strength.
Similar content being viewed by others
References
Smith H (1979) Polym Plast Technol Eng 12:141
Yen TF (1975) Recycling and disposal of solid wastes-industrial, agricultural, domestic. Ann Arbor Science, Ann Arbor, MI
Ha CS (1991) Polym Sci Technol 1:66
Roy M (1978) Polym Eng Sci 18:721
Guillet JE (1979) J Appl Polym Sci: Appl Polym Symp 35:599
Kim JK, Kang CK (1995) Polym Plast Technol Eng 34:875
Brennan LB, Isaac DH, Arnold JC (2002) J Appl Polym Sci 86:572
Eguiazabal JI, Nazabal J (1990) Polym Eng Sci 30:527
Kuczynski J, Snyder RW, Podolak PP (1994) Polym Degrad Stab 43:285
Grassie N (1977) Development in polymer degradation. Elsevier Applied Science, London
Gillen KT, Celina M (2001) Polym Degrad Stab 71:15
Sanchez P, Remiro PM, Nazabal J (1992) Polym Eng Sci 32:861
Brydson JA (1999) Plastics materials. Butterworth-Heinemann, Oxford
Adams ME, Buckley DJ, Colborn RE, England WP, Schissel DN (1993) Rapra Review Reports 6:1
Liu X (2001) Mechanical recycling of engineering thermoplastics using alloying techniques. Chalmers University of Technology, Gothenburg
Potente H, Gao X (1994) Conference proceedings of ANTEC’94, p 2989
Casale A, Salvatore O, Pizzigoni G (1975) Polym Eng Sci 15:286
Boldizar A, Möller K (2003) Polym Degrad Stab 81:359
Bai X, Isaac DH, Smith K (2007) Polym Eng Sci 47:120
Bair HE, Boyle DJ, Kelleher PG (1980) Polym Eng Sci 20:995
Davis P, Tiganis BE, Burn LS (2004) Polym Degrad Stab 84:233
ASTM STP 1294 (1996) In: Herling RJ (ed) Durability testing of nonmetallic materials, p 91
Jakubowicz I (2001) Polym Testing 20:545
Orden S (2000) Agricultura Técnica 60:3
Shimada J, Kabuki K (1968) J Appl Polym Sci 12:671
Zahn A (1997) Kunststoffe 87:314
Shimada J, Kabuki K, Ando M (1972) Rev Electr Commun Lab 20:553
Acknowledgement
J. M. Pérez thanks for a fellowship from Technology Centres Foundation Iñaki Goenaga.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Pérez, J.M., Vilas, J.L., Laza, J.M. et al. Effect of Reprocessing and Accelerated Weathering on ABS Properties. J Polym Environ 18, 71–78 (2010). https://doi.org/10.1007/s10924-009-0154-7
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10924-009-0154-7