Skip to main content
Log in

Effect of hardened steel grinding using aluminum oxide wheel under application of cutting fluid with corrosion inhibitors

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

A new category of corrosion inhibitors has been formulated. It uses water to propagate and it has been generically referred as V-active VCI®. These inhibitors promote a greater lubricity and detergency effect, used as cutting fluids; it results in less diametrical grinding wheel wear and better workpiece finishing. It can also promote the corrosion protection of the workpiece and the machine tool since the referred substance creates a protective film on the metallic surfaces, eliminating protective oils application on the parts; thus, it permits the elimination of degreasing step, reducing the number of process steps, and minimizing the environmental impact. Furthermore, it has no risk to human’s health and it is biodegradable. This paper compares the performance of the cutting fluid with V-active VCI® to a synthetic standard fluid in grinding process of AISI 4340 steel using aluminum oxide (Al2O3) grinding wheel at three different feed rates (0.25, 0.50, and 0.75 mm/min). The comparison was carried out based on the surface roughness, roundness deviation, diametrical wheel wear, acoustic emission, optical microscopy, and microhardness. The results showed that the fluid with corrosion inhibitor kept stable as the feed rate increased, which evidence the high performance of the tested fluid in severe conditions. In addition, the fluid with corrosion inhibitor was superior in almost all evaluated variables; it was unexpected since the standard fluid is consolidated in industry.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16

Similar content being viewed by others

References

  1. Soares DD, Oliveira JFG (2002) Diagnóstico de processos de retificação pela análise de sinais. Rev Máquinas Metais 436:140–157

    Google Scholar 

  2. Silva VF, Batista LN, De Robertis E, Castro CS, Cunha VS, Costa MA (2016) Thermal and rheological behavior of ecofriendly metal cutting fluids. J Therm Anal Calorim 123(2):973–980

    Article  Google Scholar 

  3. Estevao LRM, Nascimento RSV (2001) Modifications in the volatilization rate of volatile corrosion inhibitors by means of host–guest systems. Corros Sci 43(6):1133–1153

    Article  Google Scholar 

  4. Fodor GE (1985) The inhibition of vapor-phase corrosion. A Review (No. BFLRF-209). Southwest Research Inst San Antonio Txbelvoir Fuels And Lubricants Researchfacility

  5. Bastidas DM, Cano E, Mora EM (2005) Volatile corrosion inhibitors: a review. Anti-Corros Methods Mater 52(2):71–77

    Article  Google Scholar 

  6. Valdez SB, Zlatev RK, Schorr WM, Rosas GN, Dobrev T, Monev M, Krastev I (2006) Rapid method for corrosion protection determination of VCI films. Anti-Corros Methods Mater 53(6):362–366

    Article  Google Scholar 

  7. Skinner W (1993) A new method for quantitative evaluation of volatile corrosion inhibitors. Corros Sci 35(5–-8):1491–1494

    Article  Google Scholar 

  8. Genovez MC, Araújo LH, Pinto TD, Hrdina R (2015) New concept of corrosion protection in the presence of water: V-active VCI. Concept and application. Anti-Corros Methods Mater 62(1):53–58

    Article  Google Scholar 

  9. Davis JR, Associates (1996) ASM specialty handbook – carbon and alloy steels. ASM International, Metals Park

    Google Scholar 

  10. Bianchi EC, Sato BK, Sales AR, Lopes JC, de Mello HJ, de Angelo Sanchez LE et al (2018) Evaluating the effect of the compressed air wheel cleaning in grinding the AISI 4340 steel with CBN and MQL with water. Int J Adv Manuf Technol 95(5–-8):2855–2864

    Article  Google Scholar 

  11. De Martini Fernandes L, Lopes JC, Volpato RS, Diniz AE, de Oliveira RFM, de Aguiar PR et al (2018) Comparative analysis of two CBN grinding wheels performance in nodular cast iron plunge grinding. Int J Adv Manuf Technol 98(1–-4):237–249

    Article  Google Scholar 

  12. De Mello HJ, de Mello DR, Rodriguez RL, Lopes JC, da Silva RB, de Angelo Sanchez LE et al (2018) Contribution to cylindrical grinding of interrupted surfaces of hardened steel with medium grit wheel. Int J Adv Manuf Technol 95(9–-12):4049–4057

    Article  Google Scholar 

  13. Lopes JC, Ventura CE, Rodriguez RL, Talon AG, Volpato RS, Sato BK et al (2018) Application of minimum quantity lubrication with addition of water in the grinding of alumina. Int J Adv Manuf Technol 97(5–-8):1951–1959

    Article  Google Scholar 

  14. Silva LR, Corrêa EC, Brandão JR, de Ávila RF (2013) Environmentally friendly manufacturing: bBehavior analysis of minimum quantity of lubricant-MQL in grinding process. J Clean Prod. https://doi.org/10.1016/j.jclepro.2013.01.033

  15. Puerto P, Fernández R, Madariaga J, Arana J, Gallego I (2013) Evolution of surface roughness in grinding and its relationship with the dressing parameters and the radial wear. Procedia Eng 63:174–182

    Article  Google Scholar 

  16. Tawakoli T, Hadad MJ, Sadeghi MH, Daneshi A, Stöckert S, Rasifard A (2009) An experimental investigation of the effects of workpiece and grinding parameters on minimum quantity lubrication—MQL grinding. Int J Mach Tools Manuf 49(12–-13):924–932

    Article  Google Scholar 

  17. Rowe WB (2014) Principles of modern grinding technology, 2ª edn. Willian Andrew, Elsevier, UK

    Google Scholar 

  18. Yoshimura H, Itoigawa F, Nakamura T, Niwa K (2005) Development of nozzle system for oil-on-water droplet metalworking fluid and its application to practical production line. JSME Int J Ser C Mech Syst Mach Elem Manuf 48(4):723–729

    Article  Google Scholar 

  19. Belentani RDM, Funes Júnior H, Canarim RC, Diniz AE, Hassui A, Aguiar PR, Bianchi EC (2014) Utilization of minimum quantity lubrication (MQL) with water in CBN grinding of steel. Mater Res 17(1):88–96

    Article  Google Scholar 

  20. Ding K, Fu Y, Su H, Gong X, Wu K (2014) Wear of diamond grinding wheel in ultrasonic vibration-assisted grinding of silicon carbide. Int J Adv Manuf Technol 71(9–-12):1929–1938

    Article  Google Scholar 

  21. Iceri DM, Sousa RM, Destro RS, Oikawa MH, Bianchi EC, de Aguiar PR, Fortulan CA (2012) Comparação entre os métodos de aplicação de fluido de corte convencional e otimizado na retificação plana de cerâmicas. Cerâmica 58:84–89

    Article  Google Scholar 

  22. Da Silva LR, Bianchi EC, Fusse RY, Catai RE, Franca TV, Aguiar PR (2007) Analysis of surface integrity for minimum quantity lubricant—MQL in grinding. Int J Mach Tools Manuf 47(2):412–418

    Article  Google Scholar 

  23. Marinescu ID, Hitchner M, Uhlmann E, Rowe WB, Inasaki I (2006) Handbook of machining with grinding wheels. 1st ed. New York: CRC Press, 2007.

  24. De Jesus Oliveira D, Guermandi LG, Bianchi EC, Diniz AE, de Aguiar PR, Canarim RC (2012) Improving minimum quantity lubrication in CBN grinding using compressed air wheel cleaning. J Mater Process Technol 212(12):2559–2568

    Article  Google Scholar 

  25. Lee DE, Hwang I, Valente CM, Oliveira JFG, Dornfeld DA (2006) Precision manufacturing process monitoring with acoustic emission. Int J Mach Tools Manuf 46(2):176–188

    Article  Google Scholar 

  26. Marinescu ID, Rowe WB, Dimitrov B, Inasaki I (2004) Tribology of abrasive machining processes, 1ª edn. William Andrew Inc, Norwich

    Google Scholar 

Download references

Acknowledgments

Thanks to VCI Brasil for the donation of cutting fluids, for the support provided, and the opportunity for scientific and technological development provided by this research.

Funding

This study was financially supported by the Sao Paulo Research Foundation (FAPESP) (process 2017/03788-9). One of the authors thanks the CAPES (Coordination for the Improvement of HigherLevel Education Personnel) for the financial support given.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to José Claudio Lopes.

Additional information

Publisher’s note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Talon, A.G., Lopes, J.C., Tavares, A.B. et al. Effect of hardened steel grinding using aluminum oxide wheel under application of cutting fluid with corrosion inhibitors. Int J Adv Manuf Technol 104, 1437–1448 (2019). https://doi.org/10.1007/s00170-019-04005-5

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-019-04005-5

Keywords

Navigation