Abstract
In thermoforming, a heated plastic sheet is stretched into a mold cavity by applying pressure, eventually assisted by direct mechanical loading. Since upon its contact with the cold surface of the mold the sheet is prevented from undertaking any further deformation, the forming sequence induces a thickness variation in the final part. This fundamental inherent defect of thermoforming technology highly affects the optical characteristics of optical products. Therefore, the more uniform the wall thickness, the less chance optical defects will occur. In this research, the production process of a hemispherical transparent PMMA sheet as an optical product was numerically simulated. The simulated process is a two-step process comprising a combination of free forming and plug-assisted forming. In the simulation, the acrylic sheet is assumed to undergo a nonlinear and large elastic deformation which merits application of hyperelastic models. Mooney–Rivlin hyperelastic model is used as the constitutive equation. The obtained numerical results are validated with those achieved from the experiments. Different combinations of free forming and plug-assisted forming methods are studied based on what percentage of total height of the final part is produced by each method. Finally, an optimum combination of the two-step forming process is proposed. With this optimum combination, satisfactorily uniform wall thickness and minimal mold marks on the product surface will be achieved.
Similar content being viewed by others
References
Dong Y, Lin RJT, Bhattacharyya D (2005) Determination of critical material parameters for numerical simulation of acrylic sheet forming. J Mater Sci 40:399–410
Gruenwald G (1987) Thermoforming: a plastics processing guide. Technomic, Lancaster
Walczyk DF, Yoo S (2009) Design and fabrication of a laminated thermoforming tool with enhanced features. J Manuf Process 11:8–18
Chen Sh, Huanga ST, Lin M, Chien R (2008) Study on the thermoforming of PC films used for in-mold decoration. Int Comm Heat Mass Tran 35:967–973
Senn T, Waberski Ch, Wolf J, Esquivel JP, Sabaté N, Löchel B (2011) 3D structuring of polymer parts using thermoforming processes. Microelectron Eng 88:11–16
Altuglas International Arkema Inc (2006) Acrylic sheet forming manual. Altuglas International Arkema Inc., Philadelphia
Song W (1993) Large deformation finite element analysis for polymer forming processes. McMaster University, Hamilton
Hegemann B, Eyerer P (2002) Various plug assist materials and their effect on the thermoforming characteristics of polymeric sheet. SPE Annual Technical Conference, ANTEC, San Francisco
Alobaidani AD, Furniss D, Johnson MS, Endruweit A, Seddon AB (2010) Optical transmission of PMMA optical fibres exposed to high intensity UVA and visible blue light. Opt Lasers Eng 48:575–582
Dong Y, Lin RJT, Bhattacharyya D (2006) Finite element simulation of thermoforming acrylic sheets using dynamic explicit method. J Polymer Polymer Compos 14:307–328
Erchiqui F, Derdouri A, Garcia R (2002) A numerical and experimental analysis of the material behavior during a bubble inflation test. Brookfield, CT, SPE, Paper 231, Session M44-Applied Rheology
Warby MK, Whiteman JR, Jiang WG, Warwick P, Wright T (2003) Finite element simulation of thermoforming processes for polymer sheets. Math Comput Simul 61:209–218
Karamanou M, Warby MK, Whiteman JR (2006) Computational modelling of thermoforming processes in the case of finite viscoelastic materials. Comput Meth Appl Mech Eng 195:5220–5238
Sala G, Landro LD, Cassago D (2002) A numerical and experimental approach to optimise sheet stamping technologies. Polymer Thermoforming Mater Des 23:21–39
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Azdast, T., Doniavi, A., Rash Ahmadi, S. et al. Numerical and experimental analysis of wall thickness variation of a hemispherical PMMA sheet in thermoforming process. Int J Adv Manuf Technol 64, 113–122 (2013). https://doi.org/10.1007/s00170-012-4007-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-012-4007-5