Skip to main content
SpringerLink
Log in

Microstructure Aspects of Creep Resistant Welded Joints

  • Research Papers
  • Published:
Welding in the World Aims and scope Submit manuscript

Abstract

A soft zone in the welded joint, negatively influencing the creep behaviour, was detected and localised in the intercritical zone of the heat affected zone (HAZ), limiting the long-time creep strength of welds. Energy-filtering transmission electron microscopy (EFTEM) has been used for imaging precipitates and grain boundary phases in the soft zone of the HAZ and in the weld deposit of advanced ferritic martensitic Cr steels. Due to different creep duration times at a temperature of 600°C, many different precipitates and grain boundary phases and a new type of Cr-V-Nb-N rich precipitation, the so-called modified Z phase emerge in the joint. The appearance of the Cr and V rich Z phase was followed by a decrease of the population of M23C6 and MX precipitates. According to these results a decrease of the creep strength in the soft zone of the HAZ beginning after about 10,000 h was found, which seems to be in connection with the observed microstructural changes. This effect must be taken into account in the design of welded components made from this type of materials. Basic investigations using mainly the Gleeble HAZ simulation technique corroborate a drop in the hardness (soft zone) and creep resistance that occurred in the inter critical zone of the HAZ, where the peak temperature reached a level of about 900–1,000°C (zone of α/γ-transformation). This and previous investigations have shown a drop in the creep resistance for the HAZ. Compared with the base material, reductions of the creep resistance in weld samples of about 20–25% have to be taken into account. At lower stress values, the fracture location shifts from the base material towards the softened intercritical zone of the HAZ (type IV cracking). The microstructure of the HAZ shows after stressed condition pores and micro-cracks in the softened intercritical zone (temperature between Ac1 and Ac3). A correlation between the creep resistance and the size distribution of particular particle populations could not be clearly proven. For the total evaluation of the microstructural development the reduction of the dislocation density and the recovery processes (formation and growth of subgrain boundaries) must be taken into account. The tests were made on cast G-X12 CrMoWVNbN 10.1.1 parent material and Cromocord 10M weld deposit

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. H. Cerjak, P. Hofer, P. Warbichler, Microstructural evaluation of aged 9–12% Cr Steels containing W, Proc. Materials Ageing and Component Life Extension, Conf. Milano 10–12 October (1995).

  2. P. Hofer, Mikrostrukturelle Analyse als Basis für die Entwicklung neuer Kraftwerkswerkstoffe am Beispiel von G-X12 CrMoWVNbN 10-1–1, Doctoral Thesis, TU-Graz (1999).

  3. H. Cerjak, V. Foldyna, P. Hofer, B. Schaffernak, Microstructure of Advanced High Chromium Boiler Tube Steels, in: Microstructural development and stability in high chromium ferritic power plant steels, eds.: Strang A., Gooch D.J.: The Institute of Materials (1997), pp. 145–158.

  4. P. Hofer, H. Cerjak, P. Warbichler, Beitrag zur Quantifizierung der Entwicklung betriebsbedingter Ausscheidungen in neuen 9 bis 12% Cr-Stählen am Beispiel G-X12CrMoWVNbN-10-1–1, Prakt. Met. Sonderband 30 (1999), pp. 165–172.

    CAS  Google Scholar 

  5. H. Cerjak, E. Letofsky, Microstructural Aspects of the Weldability of Advanced 9–12% Cr-Steels, 5th Inter. Conf. on Tends in Welding Research, 1–5 June 1998, Pine Mountain, GA, USA.

  6. H. Cerjak, E. Letofsky, G. Feigl, P. Pichler, Characterisation of the Weldability and Behaviour of the Heat Affected Zone for Steel E911, in Materials for Advanced Power Engineering 1998, eds.: J. Lecomte-Beckers, F. Schubert, P.J. Ennis: Forschungszentrum Jülich, Energietechnik, pp. 401–410.

  7. W. Bendick, K. Haarmann, G. Wellnitz, M. Zschau, Eigenschaften der 9- bis 12-%-Chromstähle und ihr Verhalten unter Zeitstandbeanspruchung, VGB Kraftwerkstechnik 73, Heft 1 (1993).

  8. F. Brühl, Verhalten des 9%-Chromstahles X10CrMoVNb9–1 und seiner Schweißverbindungen im Kurz- und Langzeitversuch, Doctoral Thesis, TU-Graz (1989).

  9. P. Warbichler, F. Hofer, P. Hofer, E. Letofsky, On the application of energy-filtering TEM in materials science: III. Precipitates in steel, Micron Vol. 29, No. 1 (1998), pp. 63–72.

    Article  CAS  Google Scholar 

  10. F. Hofer, P. Warbichler, W. Grogger, Ultramicroscopy 59 (1995), pp. 15–31.

    Article  CAS  Google Scholar 

  11. A. Strang, V. Vodarek, Z phase formation in martensitic 12CrMoVNb steel, Materials Science and Technology, Vol.12 (1996), pp. 552–556.

    Article  CAS  Google Scholar 

  12. H. Cerjak, P. Hofer, B. Schaffernak, Beitrag zur Quantifizierung der Entwicklung betriebsbedingter Ausscheidungen in neuen 9 bis 12% Cr-Stählen, 20. Vortragsveranstaltung “Langzeitverhalten warmfester Stähle und Hochtemperaturwerkstoffe”, VDEh Düsseldorf, 28.11.1997, pp. 56–63.

  13. E.E. Underwood: Quantitative stereology, Aaddison-Wesley, Massachusetts, 1970.

    Google Scholar 

  14. L.M. Lundin, M. Hättestrand, H.O. Andrén, Redistribution of elements during ageing and creep testing of 9–12% chromium steels, in PARSONS 2000 Advanced Materials for 21st Century Turbines and Power Plant, eds.: A. Strang et al., IOM Communication (2000), pp. 601–617.

Download references

Author information

Authors and Affiliations

  1. Graz University of Technology, Austria

    E. Letofsky

Authors
  1. E. Letofsky
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Letofsky, E. Microstructure Aspects of Creep Resistant Welded Joints. Weld World 47, 3–8 (2003). https://doi.org/10.1007/BF03266395

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/BF03266395

IIW-Thesaurus keywords

Search

Navigation