Abstract
In this work, energy is harvested from circular piezoelectric materials with different boundary conditions under dynamic loading. The output of the proposed system is investigated by connecting piezo with full wave bridge rectifier (FWBR) and voltage doubler (VD) circuits. The proposed setup can be used to apply dynamic load with varying magnitude. The boundaries of the circular piezoelectric material are 3D printed using Acrylonitrile butadiene styrene (ABS) material with FDM 3D printing machine to fabricate its simple support (SS), fixed support (FS) and circular support (CS). The proposed setup utilizes a stepper motor, a display unit, a load sensor, eccentric mechanism to convert rotary motion into reciprocating motion, power supply and a compatible circuit on the printed circuit board. It is observed experimentally that the energy harvested is maximum, in case of circular support among the three applied boundary conditions and validated mathematically. The output response of the circular support boundary condition is analyzed using various combinations of three input parameters, i.e., varying dynamic load, number of strokes, two circuits and a total number of 120 experiments were performed. Artificial neural network has been applied for modeling and training between input three parameters and one output response, i.e., energy harvested. Further, genetic algorithm is applied on the ANN model to maximize the output of the system w.r.t input parameters and experimentally validated. As number of strokes (26) at dynamic load of 44 N with circular supported piezo patch connected with voltage doubler circuit gives the maximum output of 16.09 V further, when the system is tested on these parameters experimentally, it gives the 15.26 V.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Gaudenzi P (2009) Smart structures: physical behaviour, mathematical modelling and applications. J VibAcoust
Srinivasan AV, McFarland DM (2001) Smart structures, analysis and design 105(1050):458
Martinez T, Pillonnet G, Costa FA (2017) 15-mV inductor-less start-up converter using a piezoelectric transformer for energy harvesting applications. IEEE Trans Power Electron 33(3):2241–2253
Siddiqui S, Lee HB, Kim DI, Duy LT, Hanif Lee NE (2018) An omni directionally stretchable piezoelectric nanogenerator based on hybrid nanofibers and carbon electrodes for multimodal straining and human kinematics energy harvesting. Adv Energy Mater 8(2):1701520
Xu S, Shi Y, Kim SG (2006) Fabrication and mechanical property of nano piezoelectric fibres. Nanotechnology 17(17):4497
Zhao T, Fu Y, He H, Dong C, Zhang L, Zeng H, Xing L, Xue X (2018) Self-powered gustation electronic skin for mimicking taste buds based on piezoelectric enzymatic reaction coupling process. Nanotechnology 29(7):07550
Jin W, Wang Z, Huang H, Hu X, He Y, Li M, Li L, Gao Y, Hu Y, Gu H (2018) High-performance piezoelectric energy harvesting of vertically aligned Pb (Zr, Ti)O3 nanorod arrays. RSC Adv 8(14):7422–7427
Anton SR, Sodano HA (2007) A review of power harvesting using piezoelectric materials (2003–2006). Smart Mater Structures 16(3)
Kim HS, Kim JH, Kim J (2011) A review of piezoelectric energy harvesting based on vibration. Int J Precision Eng Manuf 12(6):1129–1141
Yadav M (2020) A review on piezoelectric energy harvesting systems based on different mechanical structures. Int J Enhanced Res Sci Technol Eng 9(1):1–7
Kim H, Tadesse Y, Priya S (2009) Piezoelectric energy harvesting. In Energy Harvesting Technologies. 3-39, Springer, Boston, MA.
Akaydin HD, Elvin N, Andreopoulos Y (2010) Energy harvesting from highly unsteady fluid flows using piezoelectric materials. J Intell Mater Syst Struct 21(13):1263–1278
Yadav D, Yadav J, Vashistha R, Goyal DP, Chhabra D (2019) Modeling and simulation of an open channel PEHF system for efficient PVDF energy harvesting. Mech Adv Mater Struct 1-15
Yadav J, Yadav D, Vashistha R, Goyal DP, Chhabra D (2019) Green energy generation through PEHF—a blueprint of alternate energy harvesting. Int J Green Energy 16(3):242–255
Kumar V, Chhabra D, Shukla P (2017) Xylanase production from Thermomyces lanuginosus VAPS-24 using low cost agro-industrial residues via hybrid optimization tools and its potential use for saccharification. Biores Technol 243:1009–1019
Kumar V, Kumar A, Chhabra D, Shukla P (2019) Improved biobleaching of mixed hardwood pulp and process optimization using novel GA-ANN and GA-ANFIS hybrid statistical tools. Biores Technol 271:274–282
Dhankhar R, Kumar A, Kumar S, Chhabra D, Shukla P, Gulati P (2019) Multilevel algorithm and evolutionary hybrid tools for enhanced production of arginine deiminase from Pseudomonas furukawaii RS3. Biores Technol 290:121789
Yadav M, Yadav D (2019) Micro energy generation in different kinds of water flows on lead zirconium titanite/PVDF. Int J R&D Eng Sci Manage 9(5):1–8
Yadav M, Yadav D, Kumar S, Garg RK, Chhabra D (2019) Experimental and mathematical modeling and analysis of piezoelectric energy harvesting with dynamic periodic loading. Int J Recent Technol Eng 8(3):6346–6350
Yadav J, Yadav D (2017) Design of an open channel fluid flow system for piezoelectric energy harvesting. Int J Latest Trends Eng Technol 8(4–1):244–249
Deswal S, Narang R, Chhabra D (2019) Modeling and parametric optimization of FDM 3D printing process using hybrid techniques for enhancing dimensional preciseness. Int J Interact Des Manuf 13:1–18
Benjeddou A (2004) Modeling and simulation of adaptive structures and composites: current trends and future directions. Prog Comput Struct Technol 251–80
Hong SR, Choi SB, Choi YT, Wereley NM (2005) A hydro-mechanical model for hysteretic damping force prediction of ER damper: experimental verification. J Sound Vib 285(4–5):1180–1188
Junior CD, Erturk A, Inman DJ (2009) An electromechanical finite element model for piezoelectric energy harvester plates. J Sound Vib 327:9–25
Kim HS, Kim JH, Kim J (2011) A review of piezoelectric energy harvesting based on vibration. Int J Precis Eng Manuf 12(6):1129–1141
Le TT, Han J, Jouanne AV, Mayaram K, Fiez TS (2006) Piezoelectric micro-power generation interface circuits. IEEE J Solid-State Circuits 41(6):1411–20
Mehta VK, Mehta R. Principles of electronics. S. Chand & Co. Ltd., India
Dineva P, Gross D, Müller R, Rangelov T (2014) Dynamic fracture of piezoelectric materials. AMC 10:12
Chhabra D, Bhushan G, Chandna P (2014) Multilevel optimization for the placement of piezo-actuators on plate structures for active vibration control using modified heuristic genetic algorithm. Ind Commercial Appl Smart Struct Technol 9059:90590
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Yadav, M., Yadav, D., Garg, R.K., Gupta, R.K., Kumar, S., Chhabra, D. (2021). Modeling and Optimization of Piezoelectric Energy Harvesting System Under Dynamic Loading. In: Sikarwar, B.S., Sundén, B., Wang, Q. (eds) Advances in Fluid and Thermal Engineering. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-16-0159-0_30
Download citation
DOI: https://doi.org/10.1007/978-981-16-0159-0_30
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-16-0158-3
Online ISBN: 978-981-16-0159-0
eBook Packages: EngineeringEngineering (R0)