Abstract
An orthogonal test was designed to obtain a optimized rapid aging process in order to shorten aging time. Hardness and tensile tests and TEM observation were used to evaluate the hardening response to the rapid aging process. An optimized rapid aging process, 160°C2h+200°C2h, is obtained. Under this process, the alloy has an approximately equal hardness and strength to the conventional single stage peak aging process, but the aging time of the rapid aging process is remarkably shortened, only 16.7% of the conventional process. Compared with the conventional aging process, the number density of β″ precipitates formed during the rapid aging course is reduced, however, the amount of β′ precipitates is remarkably increased. Though the contribution of the β″ precipitates to hardening is reduced, that of the high density of β′ rod precipitates is considerably increased, thus the rapid aging process produces an approximately equal hardening effect to the conventional peak aging process.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
Similar content being viewed by others
References
Jingan Liu, “Research and development of green casting Al-Si alloys inmodern automobiles,” China Journal of nonferrous metal, 11 (supplementary issue) (2001), 167–171.
Meiqiong He, “Applications of aluminum castings in the domestic and foreign automobile industries,” World Nonferrous Metals, 8 (2009), 34–35.
Runxia Li et al., “Age hardening behavior of heat-treatable Al-Si base cast alloy,” Rare Metal Materials and Engineering, 33(2) (2004), 171–175.
C. Ravi and C. Wolverton, “First-principles study of crystal structure and stability of Al-Mg-Si-(Cu) precipitates,” Acta Materialia, 52 (2004), 4213–4227.
A. K. Gupta, D. J. Lloyd, and S. A. Court, “Precipitation hardening in Al-Mg-Si alloys with and without excess Si,” Materials Science and Engineering A, 316 (2001), 11–17.
W. F. Miao and D. E. Laughlin, “ Precipitation hardening in aluminum alloy 6022,” Scripta Materialia, 40(7) (1999), 873–878.
A. Gaber et al., “Precipitation kinetics of Al-1.12Mg2Si-0.35Si and Al-1.07Mg2Si-0.33Cu alloys,” Journal of Alloys and Compounds, 429 (2007), 167–175.
G. A. Edwards et al., “ The precipitation sequence in Al-Mg-Si alloys,” Acta Materialia, 46 (1998), 3893–3904.
L. Zhen and S. B. Kang, “The effect of pre-aging on microstructure and tensile properties of Al-Mg-Si alloys,” Scripta Materialia, 36 (1997), 1089–1094.
S. Murali et al., “The effect of preaging on the delayed aging of Al-7Si-0.3Mg,” JOM, 49(2) (1997), 29–33.
D. W. Pashley, J. W. Rhodes and A. Sendorek, “Delayed aging in Al-Mg-Si Alloys: effect on structure and mechanical properties,” Journal of Historical Metallurgy, 94 (1966), 41–49.
D. W. Pashley, M. H. Jacobs and J. T. Vietz, “A Model on two step aging process of age hardenable alloys,” Philosophical Magazine, 16 (1967), 51–57.
Kuang Chen et al., “Research of new heat treatment technology for motor high properties aluminum alloy cast wheel,” Light Alloy Fabrication Technology, 34 (2006), 44–47.
Xiujun Yao, Xiufang Bian andKuibo Yin, “Influence of Interrupted Ageing on the Mechanical Properties and Microstructures of A356 Alloy,” Foundry, 54(8) (2005), 791–793.
Author information
Authors and Affiliations
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2012 TMS (The Minerals, Metals & Materials Society)
About this paper
Cite this paper
Liao, H., Wu, Y., Ding, K. (2012). Hardening Response to Rapid Aging Processes and Precipitation in Al-7%Si-0.3%Mg Alloy. In: Weiland, H., Rollett, A.D., Cassada, W.A. (eds) ICAA13 Pittsburgh. Springer, Cham. https://doi.org/10.1007/978-3-319-48761-8_167
Download citation
DOI: https://doi.org/10.1007/978-3-319-48761-8_167
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-48225-5
Online ISBN: 978-3-319-48761-8
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)