Abstract
Comparison studies have been conducted on a 1:16th scale model and a full scale tractor trailer of a variety of sealed aft cavity devices as a means to develop or enhance commercial drag reduction technology for class 8 vehicles. Eight base cavity geometries with pressure taps were created for the scale model. Drag data were acquired on the models using a 6-axis internal force balance for a range of yaw sweeps and at three Reynolds numbers for each base cavity. Pressure surveys for selected base cavities were also completed for the same yaw angles and Reynolds numbers to quantify the change in base pressure. The scale model force data indicated a marked decrease in drag at up to 12 % for two base cavity shapes, however most base cavities reduced drag by 3–10 % and a few did not decrease drag any significant amount. Pressure data indicated the base cavities increased the base pressure over baseline with a \(\Delta \mathrm{{C}}_\mathrm{{P}}\) of up to 0.3. Moreover, drag computed from pressure data implied that although the base cavities decreased the base drag due to a pressure increase, the drag may have increased elsewhere on the model. Full-scale tests were also completed using SAE Type II testing procedures. Full-scale tests on the same geometry indicated a fuel savings of over 6.5 %. Overall, the use of these devices shows to be a viable, effective and economical way to reduce fuel consumption on ground transport vehicles.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Bilanin, A.J.: Vehicle drag reducer. US Patent # 4,682,808, 1987
Boivin, M., Roberge, K.: Air drag reducing apparatus. US Patent # 6,257,654, 2001
Cooper, K.: The wind tunnel testing of heavy trucks to reduce fuel consumption. In: SAE Technical Series. 8–11 Nov 1982. SAE Paper # 821285
Cooper, K.: The effect of front-edge rounding and rear-edge shaping on the aerodynamic drag of bluff vehicles in ground proximity. In: International Congress and Exposition, Detroit, Michigan. 25 Feb–1 March, 1985. SAE Paper # 850288
Cooper, K.: Bluff-body aerodynamics as applied to vehicles. J. Wind Eng. Ind. Aerodyn. 49, 1–21 (1993)
Coon, J.D., Visser, K.D.: Drag reduction of a tractor-trailer using planar boat tail plates. In: McCallen, R., Browand, F., Ross, J. (eds.) The Aerodynamics of Heavy Vehicles: Trucks, Buses, and Trains, Lecture Notes in Applied and Computational Mechanics, vol. 19, pp. 249–265, illus (2004) With CD-ROM., Hardcover, ISBN:3-540-22088-7
Grover, K., Visser, K.D.: Over-the-road tests of sealed aft cavities on tractor trailers. In: SAE 2006 Transactions Journal of Commercial Vehicles, No. 2006-01-3529, p. 170, March 2007
Highway Statistics (Washington, DC: Annual issues), table VM-1; www.fhwa.dot.gov/policy/ohpi (2010)
Hsu, T.Y., Hammache, M., Browand, F.: Base flaps and oscillatory perturbations to decrease base drag. In: McCallen, R., Browand, F., Ross, J. (eds.) The Aerodynamics of Heavy Vehicles: Trucks, Buses, and Trains, Lecture Notes in Applied and Computational Mechanics, vol. 19, pp. 303–316, illus (2004). With CD-ROM., Hardcover, ISBN: 3-540-22088-7
Lanser, W.R., Ross, J.C., Kaufman, A.E.: Aerodynamic performance of a drag reduction device on a full-scale tractor-trailer. In: Aerospace Technology Conference and Exposition, pp. 1–9, Long Beach CA, 23–26 Sept 1991
Leuschen, J., Cooper, K.R.: Summary of Full scale wind tunnel test of aerodynamic drag-reducing devices for tractor trailers. In: Browand, F., McCallen R., Rose J. (eds.) The Aerodynamics of Heavy Vehicles: Trucks, Buses, and Trains, Lecture Notes in Applied and Computational Mechanics, vol. 41, pp. 451–462, illus (2009). With CD-ROM., Hardcover, ISBN: 978-3-85069-4
Mair, W.A.: Reduction of base drag by boat-tailed afterbodies in low speed flow. Aeronaut. Q. 20, 307–320 (1969)
Maragno, D., Visser, K.D.: Experimental optimization of non-ventilated aft cavities for tractor trailer drag reduction. In: 2003 SAE International Truck and Bus Meeting and Exhibition, Fort Worth, Texas, 10–12 Nov 2003
McCallen, R., Flowers, D., Dunn, T., Owens, J., Leonard, A., Brady, M., Browand, F., Hammache, M., Salari, K., Rutledge, W., Ross, J., Storms, B., Heineck, J.T., Driver, D., Bell, J., Zilliac, G., Walker, S.: Aerodynamic Drag of Heavy Vehicles (Class 7–8): Simulation and Benchmarking, 2000-01-2209, pp. 19–21. SAE Gov/Industry Meeting, Washington, D.C. (2000)
SAE J1321: Joint ATA/SAE Fuel Consumption Test Procedure, Type II. SAE International (1981)
SAE J1252: SAE Wind Tunnel Test Procedure for Trucks and Buses. SAE International (1981)
Saltzman, E.J., Meyer, R.R.: A Reassessment of Heavy Duty Truck Aerodynamic Design Features and Priorities. NASA/TP-1999-206574, June 1999
Transtex Composites Inc. http://www.transtexcomposite.com/home.html, 201
Acknowledgments
The authors would like to thank the New York State Energy Research & Development Authority (NYSERDA) for their support of this project.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2016 Springer International Publishing Switzerland
About this paper
Cite this paper
Kehs, J., Visser, K., Grossmann, J., Horrell, C., Smith, A. (2016). Experimental and Full Scale Investigation of Base Cavity Drag Reduction Devices for Use on Ground Transport Vehicles. In: Dillmann, A., Orellano, A. (eds) The Aerodynamics of Heavy Vehicles III. ECI 2010. Lecture Notes in Applied and Computational Mechanics, vol 79. Springer, Cham. https://doi.org/10.1007/978-3-319-20122-1_17
Download citation
DOI: https://doi.org/10.1007/978-3-319-20122-1_17
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-20121-4
Online ISBN: 978-3-319-20122-1
eBook Packages: EngineeringEngineering (R0)