Abstract
The process of drilling wells is accompanied by significant environmental pollution. From time to time, it is proposed to make threaded connectors in drill strings from high-strength and stainless steel to reduce emissions. Such steels are difficult to machine, requiring negative rake angles of threading lathe cutters. The article proposes an algorithm for calculating the accuracy of the thread profile to determine the possibility of turning it using such cutters. The result of the predictive calculation proved that using a tool with a rake angle of −7° for turning an NC13 drill thread can lead to a deviation from the nominal value of the half-profile angle, which is 40% of the size tolerance. It was shown that such a deviation could be avoided if a tool with a zero rake angle was used on the lust finish infeed of 0.035 mm.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Liakh, M., et al.: Environmentally-efficient approaches to oil and gas producing sites. In: E3S Web of Conferences, vol. 280, p. 09002 (2021). https://doi.org/10.1051/e3sconf/202128009002
Lyu, H.M., Sun, W.J., Shen, S.L., Zhou, A.N.: Risk assessment using a new consulting process in fuzzy AHP. J. Constr. Eng. Manag. 146(3), 04019112 (2020). https://doi.org/10.1061/(ASCE)CO.1943-7862.0001757
Poberezhna, L., Shkitsa, L., Poberezhnyi, L., Popovych, P., Brych, V., Shevchuk, O.: Assessment of environmental risks using elements of fuzzy logic. In: 2022 12th International Conference on Advanced Computer Information Technologies, ACIT 2022, pp. 219−222 (2022). https://doi.org/10.1109/ACIT54803.2022.9913179
Arkhypova, L.M., Mandryk, O.M., Moskalchuk, N.M., Prykhodko, M.M., Radlovska, K.O.: Renewable energy resources in the system of sustainable development of Carpathian region of Ukraine. J. Phys. Conf. Ser. 1781, 012010 (2021). https://doi.org/10.1088/1742-6596/1781/1/012010
Kravchynskyi, R., Korchemlyuk, M., Khilchevskyi, V., Arkhypova, L., Mykhailyuk, I., Mykhailyuk, J.: Spatial-factorial analysis of background status of the Danube River basin state on the northeastern slops of the Ukrainian Carpathians. J. Phys. Conf. Ser. 1781(1), 012011 (2021). https://doi.org/10.1088/1742-6596/1781/1/012011
An, Q.L., Guo, G.G., Zheng, X.H., Chen, M., Liu, G., Zhang, Y.S.: Experimental study on cutting characteristics for buttress thread turning of 13%Cr stainless steel. Key Eng. Mater. 443, 262–267 (2010). https://doi.org/10.4028/www.scientific.net/KEM.443.262
Shkitsa, L.Y., Kornuta, V.A., Kornuta, O.V., Bekish, I.O.: The model of informational space for innovation and design activities in the university. Sci. Innov. 15(6), 14–22 (2019). https://doi.org/10.15407/scine15.06.014
Kiyko, S., Druzhinin, E., Prokhorov, O., Haidabrus, B.: Multi-agent model of energy consumption at the metallurgical enterprise. In: Ivanov, V., Trojanowska, J., Pavlenko, I., Zajac, J., Peraković, D. (eds.) DSMIE 2020. LNME, pp. 156–165. Springer, Cham (2020). https://doi.org/10.1007/978-3-030-50794-7_16
Shkitsa, L., Kornuta, V., Kornuta, O., Bekish, I., Bui, V.: Information support of design innovation activity of the technical university. Manag. Syst. Prod. Eng. 28(2), 127–132 (2020). https://doi.org/10.2478/mspe-2020-0019
Dubei, O.Y., Tutko, T.F., Ropyak, L.Y., Shovkoplias, M.V.: Development of analytical model of threaded connection of tubular parts of chrome-plated metal structures. Metallofiz. Noveishie Tekhnologii 44, 251–272 (2022). https://doi.org/10.15407/mfint.44.02.0251
Shats’kyi, I.P., Lyskanych, O.M., Kornuta, V.A.: Combined deformation conditions for fatigue damage indicator and well-drilling tool joint. Strength Mater. 48, 469–472 (2016). https://doi.org/10.1007/s11223-016-9786-8
Shatskyi, I., Ropyak, L., Velychkovych, A.: Model of contact interaction in threaded joint equipped with spring-loaded collet. Eng. Solid Mech. 8(4), 301–312 (2020). https://doi.org/10.5267/j.esm.2020.4.002
Zhu, X., Zhang, Z.: Design of an ultra-high torque double shoulder drill-pipe tool joint for extended reach wells. Nat. Gas. Ind. 4(5), 374–381 (2017). https://doi.org/10.1016/j.ngib.2017.10.002
Pryhorovska, T., Ropyak, L.: Machining error influence on stress state of conical thread joint details. In: Proceedings of the International Conference on Advanced Optoelectronics and Lasers, CAOL 2019, pp. 493–497 (2019). https://doi.org/10.1109/CAOL46282.2019.9019544
Ivanov, V.: Process-oriented approach to fixture design. In: Ivanov, V., et al. (eds.) Advances in Design, Simulation and Manufacturing, pp. 42–50. Springer, Cham (2019). https://doi.org/10.1007/978-3-319-93587-4_5
Shats’kyi, I.P., Shopa, V.M., Velychkovych, A.S.: Development of full-strength elastic element section with open shell. Strength Mater. 53, 277–282 (2021). https://doi.org/10.1007/s11223-021-00286-y
Dutkiewicz, M., Velychkovych, A., Shatskyi, I., Shopa, V.: Efficient model of the interaction of elastomeric filler with an open shell and a chrome-plated shaft in a dry friction damper. Materials 15, 4671 (2022). https://doi.org/10.3390/ma15134671
Sonawane, G.D., Sargade, V.G.: Machinability study of duplex stainless steel 2205 during dry turning. Int. J. Precis. Eng. Manuf. 21, 969–981 (2020). https://doi.org/10.1007/s12541-019-00305-8
Kusyi, Y.M., Stupnytskyy, V.V., Kuk, A.M., Topilnytskyy, V.G.: Development of the fundamental diagram of the formation and transformation of the products properties during their manufacturing. J. Phys. Conf. Ser. 1781(1), 012027 (2021)
Kusyj, J., Kuk, A.: A centrifugal vibration strengthening method devised to improve technological reliability of machine parts. Eastern-Eur. J. Enterp. Technol. 1(7), 41–51 (2015)
Kusyi, Y., Stupnytskyy, V.: Optimization of the technological process based on analysis of technological damageability of castings. In: Ivanov, V., Trojanowska, J., Pavlenko, I., Zajac, J., Peraković, D. (eds.) DSMIE 2020. LNME, pp. 276–284. Springer, Cham (2020). https://doi.org/10.1007/978-3-030-50794-7_27
Zhang, G., Guo, C.: Modeling flank wear progression based on cutting force and energy prediction in turning process. Procedia Manuf. 5, 536–545 (2016). https://doi.org/10.1016/j.promfg.2016.08.044
Zaleta, O.M., Povstyanoy, O.Y., Ribeiro, L.F., Redko, R.G., Bozhko, T.Y., Chetverzhuk, T.I.: Automation of optimization synthesis for modular technological equipment. J. Eng. Sci. 10(1), A6–A14 (2023). https://doi.org/10.21272/jes.2023.10(1).a2
Ivchenko, O., et al.: Method for an effective selection of tools and cutting conditions during precise turning of non-alloy quality steel C45. Materials 15(2), 505 (2022). https://doi.org/10.3390/ma15020505
Chalyj, V., Moroz, S., Tkachuk, A., Zablotskyi, V., Trokhymchuk, I., Stelmakh, A.: Formation of bearings parts waviness in centerless mortise grinding on rigid supports. J. Eng. Sci. 10(1), A15–A21 (2023). https://doi.org/10.21272/jes.2023.10(1).a3
Kusyi, Y., Kuzin, O., Kuzin, N.: The dependence of intergrain damageability of casting on the technological treatment route. Eastern-Eur. J. Enterp. Technol. 1(5(79)), 39–47 (2016). https://doi.org/10.15587/1729-4061.2016.59845
Kusyi, Y.: Technological inheritability of product material using the criterion of technological damageability. In: Ivanov, V., Trojanowska, J., Pavlenko, I., Zajac, J., Peraković, D. (eds.) DSMIE 2021. LNME, pp. 52–61. Springer, Cham (2021). https://doi.org/10.1007/978-3-030-77719-7_6
Kusyi, Y.M., Kuk, A.M.: Investigation of the technological damageability of castings at the stage of design and technological preparation of the machine Life Cycle. J. Phys. Conf. Ser. 1426(1), 012034 (2020)
Khoshdarregi, M.R., Altintas, Y.: Generalized modeling of chip geometry and cutting forces in multi-point thread turning. Int. J. Mach. Tools Manuf. 98, 21–32 (2015). https://doi.org/10.1016/j.ijmachtools.2015.08.005
Koleva, S., Enchev, M., Szecsi, T.: Compensation of the deviations caused by mechanical deformations during machining of threads. Procedia Manuf. 13, 480–486 (2017). https://doi.org/10.1016/j.promfg.2017.09.066
Baizeau, T., Campocasso, S., Fromentin, G., Rossi, F., Poulachon, G.: Effect of rake angle on strain field during orthogonal cutting of hardened steel with c-BN tools. Procedia CIRP 31, 166–171 (2015). https://doi.org/10.1016/j.procir.2015.03.089
Yanda, H., Ghani, J.A., Haron, C.H.C.: Effect of rake angle on stress, strain and temperature on the edge of carbide cutting tool in orthogonal cutting using FEM simulation. ITB J. Eng. Technol. Sci. 42(2), 179–194 (2010). https://doi.org/10.5614/itbj.eng.sci.2010.42.2.6
Onysko, O., Panchuk, V., Kopey, V.B., Havryliv, Y., Schuliar, I.: Investigation of the influence of the cutter-tool rake angle on the accuracy of the conical helix in the tapered thread machining. In: International Conference of Applied Sciences. Journal of Physics: Conference Series, vol. 1781, p. 012028 (2021). https://doi.org/10.1088/1742-6596/1781/1/012028
Threading. Tread turning tools. Sundwik Coromant, https://www.sandvik.coromant.com/ru-ru/tools/threading-tools/thread-turning-tools. Accessed 13 Feb 2023
Berglind, L., Ziegert, J.: Modulated tool path (MTP) machining for threading applications. Procedia Manuf. 1, 546–555 (2015). https://doi.org/10.1016/j.promfg.2015.09.029
Costa, C.E., Polli, M.L.: Effects of the infeed method on thread turning of AISI 304L stainless steel. J. Braz. Soc. Mech. Sci. Eng. 43, 253 (2021). https://doi.org/10.1007/s40430-021-02978-7
Hovorun, T.P., et al.: Physical-mechanical properties and structural-phase state of nanostructured wear-resistant coatings based on nitrides of refractory metals Ti and Zr. Funct. Mater. 26(3), 548–555 (2019). https://doi.org/10.15407/fm26.03.548
Pavlenko, I., et al.: Using regression analysis for automated material selection in smart manufacturing. Mathematics 10(11), 1888 (2022). https://doi.org/10.3390/math10111888
Onysko, O., Medvid, I., Panchuk, V., Rodic, V., Barz, C.: Geometric modeling of lathe cutters for turning high-precision stainless steel tapered threads. In: Ivanov, V., Trojanowska, J., Pavlenko, I., Zajac, J., Peraković, D. (eds.) Advances in Design, Simulation and Manufacturing IV, pp. 472–480. Springer, Cham (2021). https://doi.org/10.1007/978-3-030-77719-7_47
Acknowledgment
The authors are grateful to the Ministry of Science and Education of Ukraine for the grant to implement project D-2-22-P (RK 0122U002082). The team of authors expresses their gratitude to the reviewers for valuable recommendations that have been taken into account to improve significantly the quality of this paper.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2024 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Onysko, O., Kopei, V., Vytvytskyi, V., Vriukalo, V., Lukan, T. (2024). Calculation of the Accuracy of the Drill-String NC13 Thread Profile Turned from Difficult-to-Machine Steel. In: Tonkonogyi, V., Ivanov, V., Trojanowska, J., Oborskyi, G., Pavlenko, I. (eds) Advanced Manufacturing Processes V. InterPartner 2023. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-031-42778-7_17
Download citation
DOI: https://doi.org/10.1007/978-3-031-42778-7_17
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-031-42777-0
Online ISBN: 978-3-031-42778-7
eBook Packages: EngineeringEngineering (R0)