Investigation of the Properties of Polyetheretherketone Blends and Carbon-Filled Composites Based on them

Azamat L. Slonov; Ismel V. Musov; Elena V. Rzhevskaya; Khasan V. Musov; Aslanbek F. Tlupov; Azamat A. Zhansitov

doi:10.4028/www.scientific.net/KEM.899.426

Paper Titles

The Development of Effective Multifunctional Inhibiting Additives for Polymeric Materials
p.398

Monthmorillonite as an Effective Catalyst of the Polyphenences of Polyphenylene Sulphide
p.405

Influence of Heat Treatment Conditions on the Structure and Phisicochemical Properties of Polyphenylene Sulfide
p.413

The Influence of Polyvinyl Alcohol Solutions Concentration on the Rheological and Elastic and Strength Properties of Film Materials
p.420

Investigation of the Properties of Polyetheretherketone Blends and Carbon-Filled Composites Based on them
p.426

Research on the Possibility of Recycling Medical Masks and their Use as Polymer Additives
p.434

Possible Ways to Improve Interphase Adhesion between Fiberglass and Polyphenylenesulfide
p.440

Influence of Spinneret Dimensional Parameters on Gas Separation Properties of Polysulfone Hollow Fiber Membranes
p.451

New Express Method of Non-Destructive Controlling of the Porous Structure of Asymmetric Membranes
p.456

HomeKey Engineering MaterialsKey Engineering Materials Vol. 899Investigation of the Properties of...

Investigation of the Properties of Polyetheretherketone Blends and Carbon-Filled Composites Based on them

Abstract:

The study of the properties of PEEK blends with different melt flow rate (MFR) and carbon-filled composites based on them was carried out. It was found that with an increase in the relative difference in the MFR of the blended PEEKs, there is an increase in the deviation of the experimental MFR values from the additive ones. Up to a relative difference in the MFR of the components equal to 60%, the blends obey the additivity rule. It is shown that the achievement of a certain MFR value by blending polymers with different viscosities leads to the production of materials with similar properties. Carbon-filled composites based on PEEK blends also demonstrate very similar rheological, mechanical and thermal properties, which indicates the effectiveness of the method of blending PEEKs with different viscosities to achieve the required rheological properties.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 899)

Pages:

426-433

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.899.426

Citation:

Cite this paper

Online since:

September 2021

Authors:

Azamat L. Slonov*, Ismel V. Musov, Elena V. Rzhevskaya, Khasan V. Musov, Aslanbek F. Tlupov, Azamat A. Zhansitov

Keywords:

Carbon Fiber, Composite Materials, Mechanical Properties, Polyetheretherketone, Polymer Blends, Rheological Properties, Thermal Properties

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

* - Corresponding Author

References

[1] Neelima Khare et al. Friction and Wear Characteristics of PEEK and PEEK Composites in Water Lubricated Slow Speed Sliding Tribology Online, Vol. 10, No. 1 (2015).

DOI: 10.2474/trol.10.84

Google Scholar

[2] El Magri A et al. Optimization of printing parameters for improvement of mechanical and thermal performances of 3D printed poly(ether ether ketone) parts. J Appl Polym Sci. 2020;e49087. https://doi.org/10.1002/app.49087.

DOI: 10.1002/app.49087

Google Scholar

[3] D. Garcia-Gonzalez et al. Investigation of mechanical impact behavior of short carbon-fiber-reinforced PEEK composites. Composite Structures 133 (2015) 1116–1126 https://doi.org/10.1016/j.compstruct.2015.08.028.

DOI: 10.1016/j.compstruct.2015.08.028

Google Scholar

[4] Peng Wang et al. Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing. Composites Part B 198 (2020) 108175 https://doi.org/10.1016/j.compositesb.2020.108175.

DOI: 10.1016/j.compositesb.2020.108175

Google Scholar

[5] Qiushi Li et al. Flexural Properties and Fracture Behavior of CF/PEEK in Orthogonal Building Orientation by FDM: Microstructure and Mechanism. Polymers 2019, 11, 656;.

DOI: 10.3390/polym11040656

Google Scholar

[6] Zhi Ping Xu et al. Study on mechanical properties of unidirectional continuous carbon fiber‐reinforced PEEK composites fabricated by the wrapped yarn method Polymer Composites 40(1) (2017).

DOI: 10.1002/pc.24600

Google Scholar

[7] Sabsay O.Yu., Chalaya N.M. Technological properties of thermoplastics (review). Plasticheskie massy, 1992, No. 1, pp.5-13.

Google Scholar

[8] https://www.victrex.com/en/products/polymers/peek-polymers.

Google Scholar

[9] http://instplast.ru/ru/poliefirefirketon.

Google Scholar

[10] Barvinsky I.A., Barvinskaya I.E. PM injection molding problems: underfilling. Polymer materials. 2011. No. 1. P.42-46; No. 2. P. 32-35.

Google Scholar

[11] Zhansitov A. A. et al. Synthesis and properties of polyetheretherketones for 3D printing. Fiber Chemistry, Vol. 49, No. 6, March, 2018. DOI 10.1007/s10692-018-9911-5.

Google Scholar