Distribution & Access For Publication Downloads News About Us Contact Us
Paper Titles
Study on Computer-Aided Optimizing Milling Parameters of Numerical Control Machine
p.833
Indirect Adaptive Generalized Predictive Control for an Autonomous Underwater Vehicle
p.837
A Method for Numerical Solutions to Problems with Pipes under Unknown Forces and Constraint Conditions
p.841
The Research of Processing Technique for Die-Pressing Based on FEA
p.845
Research of Fatigue Limit and Stress Concentration on Structural Steel with Double-Notches
p.849
Microstructure and Micro Mechanical Property of Part Formed by GMAW Surfacing Rapid Prototyping
p.853
Development and Experimental Study of a Small Type Submarine Mower
p.857
Studies and Application of Aquatic Processing Products Supply Chain Traceability System
p.861
Bending Fatigue Design Method for Double Sides Loaded Gears
p.865

Microstructure and Micro Mechanical Property of Part Formed by GMAW Surfacing Rapid Prototyping

Article Preview

Abstract:

The self-made metal cored wires with Fe-Si-Mn-Ti-B microalloyed series were adopted to directly form a part by gas metal arc welding (GMAW) surfacing rapid prototyping technology. The microstructure and microhardness of the part are both investigated. Its continuous metallographic microstructure along and vertical to the deposition direction shows layered characteristic, due to the special thermal cycles and cooling conditions. The microhardness values of intermediate sections of the part are much higher and stabler than those of surface sections. It is necessary to deposit a wear-resistant metal layer for enhancing the surface abradability. Among the microstructures of the part, the average nanohardness of acicular ferrite is 1.28 times than that of massive ferrite, but their Young’s modulus values are almost equivalent, which indicates acicular ferrite possesses excellent mechanical property. Therefore, achieving acicular ferrite microstructures is an appropriate means to enhance the combination property of the formed parts.

You might also be interested in these eBooks
Advanced Design and Manufacture II View Preview

Info:

Periodical:

Key Engineering Materials (Volumes 419-420)

Pages:

853-856

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.419-420.853

Citation:

Cite this paper

Online since:

October 2009

Authors:

Sheng Zhu, Chao Li, Can Duo Shen, Jian Liu

Keywords:

Acicular Ferrite, Metal Cored Wires, Microstructure, Nanohardness, Rapid Prototyping Technology (RPT)

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

References

[1] Y.M. Zhang, P.J. Li and Y.W. Chen: Mechatronics Vol. 12(2002), p.37.

Google Scholar

[2] J. Hur, K. Lee and H. Zhu: Computer-Aided Design Vol. 34(2002), p.741.

Google Scholar

[3] Z. Jandric, M. Labudovic and R. Kovocevic: International Journal of Machine Tools & Manufacture Vol. 44(2004), p.785.

Google Scholar

[4] Y.M. Zhang, P.J. Li and Y.W. Chen: Journal of Materials Processing Technology Vol. 135(2003), p.347.

Google Scholar

[5] Y.A. Song, S. Park and D.S. Choi: International Journal of Machine Tools & Manufacture Vol. 45(2005), p.1057.

Google Scholar

[6] J.H. Li and B.G. Chen: Welding Technology of China Vol. 6(2001), p.49.

Google Scholar

[7] S.S. Babu: Current Opinion in Solid State and Materials Science Vol. 8(2004), p.268.

Google Scholar

[8] B.L. Chen: Theory of Welding Metallurgy (Tsinghua University Publications, China 1991).

Google Scholar

[9] S. Liu and D.L. Olson: Welding Journal, Vol. 65(1986), p.148.

Google Scholar

Scientific.Net is a registered brand of Trans Tech Publications Ltd
© 2024 by Trans Tech Publications Ltd. All Rights Reserved