Some Considerations Concerning the Differential Scanning Calorimetry of Ultra Tough Plastic Materials

Dumitru Nedelcu; Nicoleta Monica Lohan; Constantin Carausu; Octavian Pruteanu

doi:10.4028/www.scientific.net/AMM.659.107

Paper Titles

White Cast Irons with Acoustic Properties
p.81

Influence of the Degree of Cold Drawing over the Wear Test and XRD Analysis of Pipes Used for Dampers
p.85

Considerations Concerning the Causes and Effects of the Occurrence of Residual Stresses in Metallic Materials: A Review
p.91

Hybrid Particle/Fiber Polymer Based Composites Analysis Based on DMA Data vs. Material Property Predictions
p.101

Some Considerations Concerning the Differential Scanning Calorimetry of Ultra Tough Plastic Materials
p.107

Surface Generation by Material Removal in Manufacturing Processes from Machine Building
p.112

Constitutive Parameters of Mechanical Behaviour Law for Poly (Ether-Ether-Ketone) Based Composites with Carbon Nanotubes and Carbon Fibres
p.118

Simulating the Torque and Angular Speed Distribution within a Heavy Vehicle’s Planetary Gearbox
p.127

Using Neural Networks to Modeling Vehicle Dynamics
p.133

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vol. 659Some Considerations Concerning the Differential...

Some Considerations Concerning the Differential Scanning Calorimetry of Ultra Tough Plastic Materials

Abstract:

The Differential Scanning Calorimetry (DSC) it’s an important analysis in research since the 20^th century, being used is various fields such as: physics, chemistry, science and materials technology. Its applicability has also extended to other fields, such as nanothermodynamics and bio-thermodynamics. Calorimetry measures the amount of heat absorbed/dissipated by a test sample as compared to a reference value, when the test sample is subjected to a heating and/or cooling cycle. The calorimetric effect may be revealed by the temperature-and/or time-dependent heat flow variation, and its evaluation makes sense when particular heat flow variations, specific to the various transformations accompanying temperature variation, occur. The research described in this paper focuses on the study of calorimetry of ultra tough plastic materials such B4300G4 and B4300G6. The samples were obtained by injection moulding and the planning of the experiments was achieved by means of the Taguchi methodology. The differential scanning calorimetry will show the endothermal and exothermal transformations during which we measured the transformation onset and completion temperatures, as well as the temperature in the middle of the transformation process. Also will be measured the amount of absorbed and dissipated heat, respectively. The DSC diagram showed no temperature-dependent heat flow variation that could suggest a solid state transformation. This paper aims to highlight the behavior of glass transition using DSC analysis, the transformation that occurs during heating of the two polymers obtained using three injection angles: 0^o, 45^o and 90^o.

You might also be interested in these eBooks

Advanced Concepts in Mechanical Engineering II

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volume 659)

Pages:

107-111

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.659.107

Citation:

Cite this paper

Online since:

October 2014

Authors:

Dumitru Nedelcu, Nicoleta Monica Lohan, Constantin Carausu, Octavian Pruteanu

Keywords:

Calorimetry, Injection, Ultra Tough Plastic Materials

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

References

[1] L. Feng, X. Bian, G. Li, Z. Chen, Yi Cui, X. Chen, Determination of ultra-low glass transition temperature via differential scanning calorimetry, Polymer Testing 32 (2013), 1368–1372.

DOI: 10.1016/j.polymertesting.2013.08.015

Google Scholar

[2] M.J. Richardson, Thermal analysis of polymers using quantitative differential scanning calorimetry, Polym. Test. 4 (1984), 101–115.

Google Scholar

[3] C. Schick, Calorimetry, Polymer Science: A Comprehensive Reference, 2, (2012), 793–823.

Google Scholar

[4] W. Sun, A.P. Vassilopoulos, T. Keller, Effect of thermal lag on glass transition temperature of polymers measured by DMA, International Journal of Adhesion & Adhesives, 52, (2014), 31–39.

DOI: 10.1016/j.ijadhadh.2014.03.009

Google Scholar

[5] D. Nedelcu, O. Pruteanu, Aspecte ale formarii canelurilor exterioare prin deformare plastic la rece utilizand metoda Taguchi, Tehnica-Info Publishing House, 243-261, Chisinau, (2000).

Google Scholar

[6] C. Schick, Glass transition under confinement-what can be learned from calorimetry, Eur. Phys. J. Special Topics 189, (2010), 3–36.

DOI: 10.1140/epjst/e2010-01307-y

Google Scholar

[7] T.D. Mindru, S. Andrei, C. Burian, Finite element analysis of samples injected by Polyamide 6. 6 Nature, Int J of Modern Manufacturing Technology, Vol. IV, No. 2/2012, 47-54.

Google Scholar

[8] I. Seres, Injectarea materialelor plastice Imprimeria de Vest Publishing House, (1996), 314–25.

Google Scholar

[9] M. Płaczek, Indication of the suitable model of a mechatronic system as an introduction to the synthesis task, J Achievements Mater Manuf Eng, JAMME, (2011), 49/2(December), 338–49.

Google Scholar

[10] R. Comaneci, L. Zaharia, R. Chelariu, Damaging prediction of difficult-to-work aluminum alloys during equal channel angular pressing, J Mater Eng Proc, (2012), 21, 287–97.

DOI: 10.1007/s11665-011-9904-5

Google Scholar