Manufacturing Technology 2017, 17(1):84-86 | DOI: 10.21062/ujep/x.2017/a/1213-2489/MT/17/1/84

Theoretical Regulation of Delimitation of Metal Level Decrease in the Furnace in Case of Pneumatic Dosing Device of Metal

Juraj Ružbarský, Rastislav Majerník
Faculty of Manufacturing Technologies with a seat in Prešov, Technical University of Košice, Štúrova 31, 080 01 Prešov, Slovakia

Article deals with the during operation of pneumatic dosing device designed for die casting machines where the metal level in the furnace decreases stepwise by which the period of dosing of the filling mould is prolonged. We also deal the regulation of delimitation of metal level decrease in the furnace based upon the pneumatic principle.

Keywords: Theoretical Regulation; Die casting; Air pressure; Dosing device

Published: February 1, 2017  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Ružbarský J, Majerník R. Theoretical Regulation of Delimitation of Metal Level Decrease in the Furnace in Case of Pneumatic Dosing Device of Metal. Manufacturing Technology. 2017;17(1):84-86. doi: 10.21062/ujep/x.2017/a/1213-2489/MT/17/1/84.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. BOLIBRUCHOVÁ, D., RICHTÁRECH, L. (2016). Possibilities of Using Al-Si-Mg Alloys with Higher Fe Content for Demanding Castings. In: Manufacturing Technology, Vol. 16, pp. 317-323, ISSN 1213-2489 Go to original source...
    2. BORKOWSKI, S., INGALDI, M., SYGUT, P., KLIMECKA-TATAR, D. (2016). Stability of the Casting Process According to the Method BOST. In: Manufacturing Technology, Vol. 16, pp. 26-29, ISSN 1213-2489 Go to original source...
    3. BLATNICKÝ, M., DIŽO, J. (2016). Design of a Three-Finger Robot Manipulator. In: Manufacturing Technology, Vol. 16, pp. 485-489, ISSN 1213-2489 Go to original source...
    4. JENČURÁKOVÁ, D., PALENČÁR, R. (2016). Optimizing Management of the Measurement System of the Technological Process. In: Manufacturing Technology, Vol. 16, pp. 107-113, ISSN 1213-2489 Go to original source...
    5. MACHUTA, J., NOVA, I. (2016). Analysis of Heat Transfer Conditions in the Sand and Metal Moulds and Their Effect on the Solidification of the Casting. In: Manufacturing Technology, Vol. 16, pp. 380-384, ISSN 1213-2489 Go to original source...
    6. NOVÁ, J., NOVÁKOVÁ,J., BRADAČ,J. (2006). Technologie I, TU Liberec, p. 89
    7. PAŠKO, J. et al. (2014). Die casting defects of castings from silumin. In: Applied Mechanics and Materials, Vol. 2014, No. 510, pp. 91-96. Go to original source...
    8. RAGAN, E. et al. (2007). Liatie kovov pod tlakom, FVT 2007, Prešov, 392 p.
    9. RUŽBARSKÝ, J. (2014). Dynamics of core taking out at die casting. In: Applied Mechanics and Materials, Vol. 2014, No. 616, pp. 244-251. Go to original source...
    10. RUŽBARSKÝ, J., PAŠKO, J., GAŠPÁR, Š. (2014). Techniques of die casting. RAM-Verlag, 199 p.

    Return to the content