Conventional lithography

Photolithography is the most prevalent micro- and nanoscale patterning technique due to its effectiveness and efficiency. The process is illustrated in Figure 1. The term photolithography has a literal translation of “to write in stone using light,” based on the Greek roots of the term. Typically, the “stone” is a silicon wafer coated with a light-sensitive polymer. Patterns of light (or electrons/ions) focused onto this coating change the solubility of the polymer in localized regions. The coating that remains after dissolving (i.e., developing) the soluble regions protects the substrate from subsequent processing, such as etching. The coating is therefore called a “photoresist,” because it is designed to be sensitive to light and to resist etching. A pattern emerges on the substrate after etching the exposed regions and removing the photoresist.

Figure 1
figure 1

Conventional photolithography (and other “beambased” lithographies) focuses patterns of photons, electrons, or ions onto a substrate coated with a thin polymeric fi lm called a photoresist. In the case of photolithography, the absorbed photons cause chemical reactions that change the solubility of the photoresist. Openings in the sacrifi cial photoresist locally expose the substrate to subsequent processing steps, such as etching. Credit: Ying Liu (North Carolina State University).

Conventional photolithography is the cornerstone technology that enables fabrication in modern electronics. However, it also has many limitations, including (1) the need for a mask, focusing optics, light-sensitive materials, and expensive specialized equipment; (2) resolution limits defined by optics; and (3) poor compatibility with unconventional materials that may be soft, nonplanar, or difficult to process. Other “beam-based” lithography techniques, such as electron-beam lithography, can provide higher-resolution patterns than photolithography without the need for a mask, but otherwise, suffer similar limitations.

Approaches to address the challenges of conventional lithography

To address these issues, there have been numerous alternative (or “unconventional”) approaches,13 including, for example, soft lithography,4 contact printing,5 dip-pen lithography,6 imprint lithography,7 and three-dimensional (3D) printing.8 No single method addresses all of the limitations of photolithography, and therefore, choosing a patterning method depends on the application, the materials, and the resources available.

Among these alternate methods, self-organization—the formation of patterns by harnessing forces across a range of scales—is an attractive option as it (1) forms complex patterns with minimal process monitoring and control, (2) can make structures beyond the resolution limit of photolithography, and (3) often provides more sustainable routes for fabrication by using ambient energy or minimizing environmental hazards. The contributions in this issue summarize key advances in self-organization using molecular-scale forces (block copolymer [BCP] self-assembly), capillary forces (capillary-induced assembly), and mechanical forces (instability-induced patterning).

In addition, this issue covers self-folding (origami) and kirigami as “pattern transforming” methods that give two-dimensional (2D) patterns a greater degree of freedom to bend, extend, or fold. While conventional lithography is inherently planar, self-folding can create out-of-plane and 3D structures by harnessing responsive materials and managing mechanical stress. Kirigami utilizes strategic cuts in materials to allow otherwise rigid materials to extend significantly both in and out of plane.

Taken together, these new approaches open many scientific and engineering opportunities for micro- and nanoscale patterning by coupling disciplines, including physics, chemistry, biology, mechanics, and materials science, while providing new and versatile material functionalities. The field is truly multidisciplinary.

Examples and applications

To provide context, we offer several examples of self-organized and self-folded structures and their applications. For example, BCP self-assembly has been used for making structures beyond the resolution limit of optical lithography. BCPs are composed of two or more chemically distinct polymer segments. These segments self-assemble by phase-separating into small domains with geometries that can be tuned based on a number of factors, including the length and composition of the polymer. The resulting structures can be utilized as templates for high-density information storage,9 nanoelectronics,10 photonic crystals,11 and complex 3D structures (Figure 2a–c)12 that are difficult to make using conventional lithography.

Figure 2
figure 2

Applications of different approaches. (a) Scanning electron microscope (SEM) image of an etched [(0 1),(2 0)] bilayer structure on a substrate, (b) magnifi ed SEM images (red and green borders refer to Figure 2a ), and (c) cross-sectional SEM image of the regions inside and outside the template. 12 © 2012 American Association for the Advancement of Science. (d–f) Images showing the contact angle of a water drop: (d) 152 ° on highly crumpled graphene, (e) 103 ° on unfolded graphene, and (f) 105 ° on bare polydimethylsiloxane substrate. 14 © 2013 Nature Publishing Group. (g) A single polystyrene sphere trapped through the capillary-assisted conformal wrapping of epoxy nanobristles. (h) Coiled whirlpools remain after the removal of the spheres. 19 © 2009 American Association for the Advancement of Science. (i–j) SEM images of fi ngers of gold-coated polymeric structures in (i) open position and (j) closed position after molecule trapping, driven by capillary interaction. (k) Schematic of molecules trapped in the nanogaps of the fi ngers, and (l) distribution of electric-fi eld intensity (color bar scale) at 750 nm for four Au fi ngertips of 68-nm radius. Reproduced with permission from Reference 23. © 2010 American Chemical Society. (m–n) Images of micropillar arrays (m) before and (n) after clustering. Two different colors result from Bragg diffraction of micropillar arrays with different periodicities, with clustering resulting in surface whitening. Reproduced with permission from Reference 24. © 2009 American Chemical Society.

Surface instabilities such as wrinkling, offer another approach to achieve patterning by self-organization. These instabilities form typically by minimizing energy between competing forces and have been used for applications such as controlled adhesion 13 and wetting (Figure 2d–f),14 anti-biofouling,15 and tunable color.16

Capillary-induced self-organization can generate a range of structures based on the application of capillary forces to structures. Although capillary forces can self-assemble freestanding rigid structures by attracting floating objects (e.g., breakfast cereal in the “Cheerios effect”),17,18 here, we focus on capillary forces that deform micro-/nanostructures attached to a substrate. This approach, which allows greater structural complexity from features defined lithographically, has been utilized for microparticle trapping and release (Figure 2g–h),1922 molecule trapping and detection (Figure 2i–j),23 and whitening by surfaces that scatter light (Figure 2m–n).24

Self-folding has been used in various applications, including self-folding robots (Figure 3a–b),25 microgrippers (Figure 3d–f),26 solar cells,27 and origami antennas.28 The use of strategic cuts in materials followed by folding (kirigami) enables, for example, the formation of stretchable electrodes for nonplanar devices (Figure 3c)29 and solar cells with integrated solar tracking.30

Figure 3
figure 3

(a) A robot begins in a fl at conformation, and folding is initiated 10s after the batteries are connected. (b) Once the fi nal folds cool and become rigid, the robot is assembled and ready for operation. Reproduced with permission from Reference 25. © 2014 American Association for the Advancement of Science. (c) A proof of concept for a stretchable electrode platform is shown by embedding fractal cuts in a silicone rubber sheet coated with a thin conducting fi lm and conformably wrapping the structure around a spherical baseball without wrinkles. The green light-emitting diode remains lit after wrapping. Reproduced with permission from Reference 29. © 2014 National Academy of Sciences. (d) Schematic of the behavior of a self-folding microgripper, (e) schematic of a microgripper, and (f) capture and excision of cells from a live cell fi broblast clump (dyed green). Reproduced with permission from Reference 26. © 2015 American Chemical Society.

Structures formed by self-folding and self-organization can be classified based on their characteristic length scales, range of materials, and form factors, as summarized in Table I. For the form factors, mesostructure refers to a (surface-attached) structure approximately in the range of nanometer to micrometer scale. Film refers to planar features such as a coating or shell. Bulk refers to a mass of material typically bigger than the micrometer scale. These approaches cover a broad range of length scales and provide routes for making hierarchical structures.10 These methods are also compatible with diverse classes of materials and can be shaped into different forms.

Table I Length scales, materials, and forms covered by different approaches.

In this issue

The articles in this issue of MRS Bulletin highlight and detail some of the recent progress in patterning approaches based on self-organization and self-folding. The article by Bai and Ross summarizes state-of-the-art applications of molecular self-assembly by controlling the composition and interactions of BCPs. This elegant approach to patterning is on the International Technology Roadmap for Semiconductors31 as a contender to replace or supplement conventional lithography for the fabrication of advanced electronics. Tawfick et al. illustrate ways to generate various 3D structures by self-assembly of filamentary materials through interactions among capillary, elastic, and adhesion forces. This approach enables formation of complex patterns that cannot be made using conventional lithography methods.

In their article, Wang and Zhao provide guidelines to control various topographic patterns by harnessing surface instabilities. This approach to patterning is noted for its simplicity and applicability to a wide range of length scales. Rogers et al. discuss self-folding to form out-of-plane, functional micro- and nanostructures. This approach allows transformation of 2D micro-/nanoscale structures into desired 3D shapes at length scales that are challenging for conventional fabrication tools. Finally, Yang et al. highlight the design and fabrication of super-conformable, foldable materials via fractal cuts and lattice kirigami. This approach enables otherwise rigid materials to extend significantly both in and out of plane.

Summary

Pattern formation by self-organization and self-folding provides unique opportunities for the materials community by addressing many of the issues associated with conventional lithography. With the exception of BCPs, the methods described in this issue are not envisioned to compete with conventional lithography for fabricating state-of-the-art electronics. The methods discussed here generally lack the alignment and precision necessary for high-yield processing of electronic materials. Instead, these new approaches typically seek to control and pattern diverse materials across a range of length scales at low cost in a way that gives rise to new functionalities. This brings up many interesting and challenging scientific questions, suggests new ways of designing and fabricating structures and devices, and enables applications previously unattainable. For example, kirigami enables stretchable structures from rigid materials, self-folding enables the formation of 3D structures from 2D structures, capillary assembly gives rise to dynamic structures, and instabilities create patterns at a low cost. As conventional lithography has empowered the materials community after decades of research and development, it is anticipated that self-organization and self-folding will provide many exciting opportunities beyond conventional lithography.