Abstract
To test a newly developed nuclear fuel, a test rig needs to be made and put into the core of a research reactor. Then, high temperature and highly pressurized coolant is circulated through the test rig during the irradiation test to transfer the heat generated by the fissile activity of the nuclear fuel. Because several decades of instrumentation cables are drawn from a test rig, it is difficult to seal out the coolant in the test rig. In this study, a mechanical sealing method which uses flake type graphite powder has been developed to replace the conventional brazing process. The internal design of the test rig is modified to apply compressive stress on the graphite powder to seal out the gap between the sealing plug and instrumentation cables. The sealing performance is then verified by a hydraulic pressure test and Helium leak test according to the ASME code, section III.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
Abbreviations
- T:
-
Torque induced on a screw
- K:
-
Torque coefficient
- D:
-
Diameter of a screw
- N:
-
Axial force of a screw
References
Hwang, Y. H., Kim, J. Y., Lee, H. K., Koh, J. H., and Oh, S.Y., “A study on the Comparison of Brazed Joint of Zircaloy-4 with PVDBe and Zr-Be Amorphous alloys as Filler Metals,” Journal of Korea Academia-Industrial cooperation Society, Vol. 7, No. 2, pp. 113–119, 2006.
Shim, K. T., Cho, M. S., and Choo, K. N., “A study on the Brazing using Inconel 600 and STS 310 Materials,” Journal of the Korean Society of Mechanical Technology, Vol. 13, No. 2, pp. 145–153, 2011.
Cho, M. S. and Choo, K. N., “Development of an Irradiation Device for High Temperature Materials in HANARO,” Journal of the Korean Society of Mechanical Technology, Vol. 13, No. 2, pp. 145–153, 2011.
Wang, Y. Q., Afsar, A. M., and Song, J. I., “Optimization of brazing conditions for OFHC Cu and ASTM A501 low carbon steel by taguchi method,” Int. J. Precis. Eng. Manuf., Vol. 10, No. 3, pp. 97–104, 2009.
Jeong, H. Y., Hong, J. T., Ahn, S. H., Joung, C. Y., Lee, J. M., and Lee, C. Y., “Development of Sealing Technology for Instrumentation Feedthrough of High Pressure Vessel,” Journal of the Korean Society of Mechanical Technology, Vol. 13, No. 2, pp. 137–143, 2011.
Tung, S. K. and Lim, L. C., “Wide gap brazing of nickel base braze mixes,” Mater. Sci. Technol., Vol. 11, pp. 949–954, 1995.
We, X. W., Chandel, R. S., Seow, R. S., and Li, H., “Wide gap brazing of stainless steel to nickel-based superalloy,” J. Mater. Process. Tech., Vol. 113, pp. 215–221, 2001.
Geront’ev, A. E., Strakhov, A. A., Konyushkov, A. G., and Alekseev, D. E., “Upgrading of the sealing units of steam generator in nuclear power plants with VVER-440 and -1000 reactors,” Atomic Energy, Vol. 99, No. 6, pp. 906–910, 2005.
Anikeenko, V. A., Ionov, S. G., Levin, V. N., Gulyaeva, E. S., Karlov, V. V., Polyakova, N. S., and Prodan, V. D., “Leak tightness of detachable joints with heat-expanded graphite gaskets,” Chemical and Petroleum Engineering, Vol. 43, No. 11–12, pp. 740–743, 2007.
Jeong, H. Y., Hong, J. T., Joung, C. Y., and Ahn, S. H., “Mechanical Sealing Method for Instrumentation Feedthrough of High Pressure Vessel,” Journal of the Korean Institute of Plant Engineering, Vol. 16, No. 3, pp. 123–129, 2011.
ASME, “Rules for construction of nuclear facility components,” ASME Boiler and Pressure Vessel Code, Sec III, Subsection NB-6000, 2007.
Hong, J. T., Ahn, S. H., Joung, C. Y., and Jeong, H. Y., “Assembly type funnel,” KAERI, KHNP, KR 10-2012-0068114.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hong, J., Ahn, SH., Jeong, HY. et al. Development of graphite sealing technique for an irradiation test rig of nuclear fuels. Int. J. Precis. Eng. Manuf. 14, 797–803 (2013). https://doi.org/10.1007/s12541-013-0104-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-013-0104-0