Skip to main content
Log in

Self-sustained catalytic combustion of CO enhanced by micro fluidized bed: stability operation, fluidization state and CFD simulation

  • Research Article
  • Published:
Frontiers of Environmental Science & Engineering Aims and scope Submit manuscript

Abstract

A micro fluidized bed reactor was used to study the self-sustaining catalytic combustion of carbon monoxide (CO). The Cu1−xCexOy catalyst, as well as the pure CuO and CeO2, are used to investigate the contributing mechanism of different active sites including dispersed CuO and Cu—Ce solid solutions. The ignition temperature (Ti) of CO over these catalysts at a flow rate of 2000 mL/min followed the order: 74 °C (Cu0.5Ce0.5Oy) < 75 °C (Cu0.25Ce0.75Oy) < 84 °C (Cu0.75Ce0.25Oy) < 105 °C (CuO) < 500 °C (CeO2). Furthermore, the lean combustion limits (equivalence ratio ϕ) over these catalysts under the flow rates of 750–3000 mL/min (through fixed, bubbling, and fluidized bed) were also measured, which are Cu0.5Ce0.5Oy < Cu0.25Ce0.75Oy < Cu0.75Ce0.25Oy < CuO < CeO2. The fluidized bed was simulated using the Eulerian two-fluid model (TFM) coupled with a diffusion/kinetic-limited reaction model to evaluate the influence of operation conditions on the self-sustained combustion of CO. The predicted maximum temperature agreed with the experimental measurements, demonstrating the validity of the kinetic model and simulation parameters. The results of catalytic combustion with increasing CO concentrations suggest that the catalytic combustion reaction could co-exist with the flamed combustion. When a high concentration of CO is used, a blue-purple flame caused by CO combustion appears in the upper part of the fluidized bed, indicating that the range of CO-containing exhaust gas purification could be expanded to a larger range using the fluidized-bed catalytic combustion technique.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Similar content being viewed by others

References

  • Águila G, Gracia F, Araya P (2008). CuO and CeO2 catalysts supported on Al2O3, ZrO2, and SiO2 in the oxidation of CO at low temperature. Applied Catalysis A, General, 343(1–2): 16–24

    Article  Google Scholar 

  • Avgouropoulos G, Ioannides T (2003). Selective CO oxidation over CuO–CeO2 catalysts prepared via the urea—nitrate combustion method. Applied Catalysis A, General, 244(1): 155–167

    Article  CAS  Google Scholar 

  • Avgouropoulos G, Ioannides T, Matralis H (2005). Influence of the preparation method on the performance of CuO—CeO2 catalysts for the selective oxidation of CO. Applied Catalysis B: Environmental, 56(1–2): 87–93

    Article  CAS  Google Scholar 

  • Benyahia S (1994). Synthesis gas formation by catalytic oxidation of methane fluidized bed reactors. Powder Technology, 146(1–2): 11–21

    Google Scholar 

  • Bin F, Kang R, Wei X, Hao Q, Dou B (2019). Self-sustained combustion of carbon monoxide over CuCe0.75Zr0.25Oδ catalyst: stability operation and reaction mechanism. Proceedings of the Combustion Institute, 37(4): 5507–5515

    Article  CAS  Google Scholar 

  • Bin F, Wei X, Li B K S, Hui K S (2015). Self-sustained combustion of carbon monoxide promoted by the Cu—Ce/ZSM-5 catalyst in CO/O2/N2 atmosphere. Applied Catalysis B: Environmental, 162: 282–288

    Article  CAS  Google Scholar 

  • Bizon K (2016). Autothermicity, multiplicity, yield and selectivity of catalytic processes in a polytropic fluidized bed reactor. Chemical Engineering Journal, 288: 834–844

    Article  CAS  Google Scholar 

  • Chen A, Yu X, Zhou Y, Miao S, Li Y, Kuld S, Sehested J, Liu J, Aoki T, Hong S, et al. (2019). Structure of the catalytically active copper—ceria interfacial perimeter. Nature Catalysis, 2(4): 334–341

    Article  CAS  Google Scholar 

  • Chen Y, Liu D, Yang L, Meng M, Zhang J, Zheng L, Chu S, Hu T (2013). Ternary composite oxide catalysts CuO/Co3O4—CeO2 with wide temperature-window for the preferential oxidation of CO in H2-rich stream. Chemical Engineering Journal, 234: 88–98

    Article  CAS  Google Scholar 

  • Du P, Wang W, Jia C, Song Q, Huang Y, Si R (2016). Effect of strongly bound copper species in copper—ceria catalyst for preferential oxidation of carbon monoxide. Applied Catalysis A, General, 518: 87–101

    Article  CAS  Google Scholar 

  • Dubinin Y, Yazykov N, Reshetnikov S, Yakovlev V (2021). Catalytic combustion of sulfur-containing liquid fuels in the fluidized bed: experiment and modeling. Journal of Industrial and Engineering Chemistry, 93: 163–169

    Article  CAS  Google Scholar 

  • Duyar M, Ramachandran A, Wang C, Farrauto R (2015). Kinetics of CO2 methanation over Ru/γ-Al2O3 and implications for renewable energy storage applications. Journal of CO2 Utilization, 12: 27–33

    Article  CAS  Google Scholar 

  • Girimonte R, Formisani B (2009). The minimum bubbling velocity of fluidized beds operating at high temperature. Powder Technology, 189(1): 74–81

    Article  CAS  Google Scholar 

  • Goshima T, Yoshida Y, Shimazaki K, Fukudome K, Mizuta K, Nii S (2017). Experimental investigation on gas-solid behavior in fluidized beds with superfine particles. Chemical Engineering & Technology, 40(12): 2295–2304

    Article  CAS  Google Scholar 

  • Gu C, Qi R, Wei Y, Zhang X (2018). Preparation and performances of nanorod-like inverse CeO2—CuO catalysts derived from Ce-1,3,5-Benzene tricarboxylic acid for CO preferential oxidation. Reaction Kinetics, Mechanisms and Catalysis, 124(2): 651–667

    Article  CAS  Google Scholar 

  • Hu C, Zhu Q, Jiang Z, Chen L, Wu R (2009). Catalytic combustion of dilute acetone over Cu-doped ceria catalysts. Chemical Engineering Journal, 152(2–3): 583–590

    Article  CAS  Google Scholar 

  • Iamarino M, Chirone R, Pirone R, Russo G, Salatino P (2002). Catalytic combustion of methane in a fluidized bed reactor under fuel-lean conditions. Combustion Science and Technology, 174(11–12): 361–375

    Article  CAS  Google Scholar 

  • Jia A, Hu G, Meng L, Xie Y, Lu J, Luo M (2012). CO oxidation over CuO/Ce1−xCuxO2−δ and Ce1−xCuxO2−δ catalysts: synergetic effects and kinetic study. Journal of Catalysis, 289: 199–209

    Article  CAS  Google Scholar 

  • Jia C, Dai Y, Yang Y, Chew J (2020). A fluidized-bed model for NiMgW-catalyzed CO2 methanation. Particuology, 49: 55–64

    Article  CAS  Google Scholar 

  • Kang R, Ma P, He J, Li H, Bin F, Wei X, Dou B, Hui K, Hui K (2021). Transient behavior and reaction mechanism of CO catalytic ignition over a CuO—CeO2 mixed oxide. Proceedings of the Combustion Institute, 38(4): 6493–6501

    Article  CAS  Google Scholar 

  • Kang R, Wei X, Ma P, Bin F, He J, Hao Q, Dou B (2020). Self-sustained combustion of CO with transient changes and reaction mechanism over CuCe0.75Zr0.25Oδ powder for honeycomb ceramic catalyst. Fuel, 263: 116637

    Article  CAS  Google Scholar 

  • Lazarovici A, Kalliadasis S, Merkin J, Scott S, Simon P (2004). The propagation and inhibition of an exothermic branched-chain flame with an endothermic reaction and radical scavenging. Journal of Engineering Mathematics, 49(1): 41–55

    Article  CAS  Google Scholar 

  • Li J, Yao X, Liu L, Zhong X, Lu C (2021). Heat transfer characterization and improvement in an external catalyst cooler fluidized bed. Particuology, 56: 103–112

    Article  CAS  Google Scholar 

  • Li J, Zhu Q, Peng W, Zhang Q, Luo G, Wei F (2017). Novel hierarchical Ni/MgO catalyst for highly efficient CO methanation in a fluidized bed reactor. AIChE Journal. American Institute of Chemical Engineers, 63(6): 2141–2152

    Article  CAS  Google Scholar 

  • Liang W, Li X, Ju H, Ren S (2022). Adsorption and dissociation mechanism of toluene on Pd (111) and PdO (101) surface: first principle calculation. Surface Science, 720: 122051

    Article  CAS  Google Scholar 

  • Liu B, Ji S (2013). Comparative study of fluidized-bed and fixed-bed reactor for syngas methanation over Ni—W/TiO2—SiO2 catalyst. Journal of Energy Chemistry, 22(5): 740–746

    Article  Google Scholar 

  • Liu Q, Chen R, Zeng M, Fei Z, Chen X, Zhang Z, Tang J, Cui M, Qiao X (2020a). High-efficiency treatment of benzaldehyde residue using two-stage fluidized-bed/fixed-bed catalytic system. Environmental Technology, 41(22): 2898–2906

    Article  CAS  Google Scholar 

  • Liu X, Xu G, Gao S (2008). Micro fluidized beds: wall effect and operability. Chemical Engineering Journal, 137(2): 302–307

    Article  CAS  Google Scholar 

  • Liu Y, Mao D, Yu J, Zheng Y, Guo X (2020b). Facile preparation of highly active and stable CuO—CeO2 catalysts for low-temperature CO oxidation via a direct solvothermal method. Catalysis Science & Technology, 10(24): 8383–8395

    Article  CAS  Google Scholar 

  • Luo M, Fang P, He M, Xie Y (2005). In situ XRD, Raman, and TPR studies of CuO/Al2O3 catalysts for CO oxidation. Journal of Molecular Catalysis A, Chemical, 239(1–2): 243–248

    Article  CAS  Google Scholar 

  • Meng F, Xia Y, Zhang J, Qiu D, Chu Y, Tang Y (2021). Cu/Cr co-stabilization mechanisms in a simulated Al2O3—Fe2O3—Cr2O3—CuO waste system. Frontiers of Environmental Science & Engineering, 15(6): 116

    Article  CAS  Google Scholar 

  • Nam H, Kim J, Kim H, Kim M, Jeon S, Jin G, Won Y, Hwang B, Lee S, Baek J, et al. (2021). CO2 methanation in a bench-scale bubbling fluidized bed reactor using Ni-based catalyst and its exothermic heat transfer analysis. Energy, 214: 118895

    Article  CAS  Google Scholar 

  • Paasikallio V, Kalogiannis K, Lappas A, Lehto J, Lehtonen J (2017). Catalytic fast pyrolysis: influencing bio-oil quality with the catalyst-to-biomass ratio. Energy Technology (Weinheim), 5(1): 94–103

    Article  CAS  Google Scholar 

  • Parmon V, Simonov A, Sadykov V, Tikhov S (2015). Catalytic combustion: achievements and problems. Combustion, Explosion, and Shock Waves, 51(2): 143–150

    Article  Google Scholar 

  • Rau J, Chen J, Lin M, Wey M (2010). Removal the coal ash, NO, and SO2 simultaneously by the fluidized-bed catalyst reactor. Energy & Fuels, 24(3): 1711–1719

    Article  CAS  Google Scholar 

  • Talluri B, Yoo K, Kim J (2022). In situ growth of self-composed cerium iron oxide hierarchal structures as a novel anode electrocatalyst for direct methanol fuel cells. Ceramics International, 48(3): 3628–3635

    Article  CAS  Google Scholar 

  • Wang F, Fu R, Hu R, Ding R (2013). Reactors used for catalytic combustion of methane. Advanced Materials Research, 634–638: 798–804

    Google Scholar 

  • Wang Z, Li R, Chen Q (2015). Enhanced activity of CuCeO catalysts for CO oxidation: influence of Cu2O and the dispersion of Cu2O, CuO, and CeO2. Chemphyschem: a European Journal of Chemical Physics and Physical Chemistry, 16(11): 2415–2423

    Article  CAS  Google Scholar 

  • Wang X, Jin Y, Chen W, Zou R, Xie J, Tang Y, Li X, Li L (2021). Electro-catalytic activity of CeOx modified graphite felt for carbamazepine degradation via E-peroxone process. Frontiers of Environmental Science & Engineering, 15(6): 122

    Article  CAS  Google Scholar 

  • Yang Z, Yang P, Zhang L, Guo M, Yan Y (2014). Investigation of low concentration methane combustion in a fluidized bed with Pd/Al2O3 as catalytic particles. RSC Advances, 4(103): 59418–59426

    Article  CAS  Google Scholar 

  • Zeng S, Zhang W, Liu N, Su H (2013). Inverse CeO2/CuO catalysts prepared by hydrothermal method for preferential CO oxidation. Catalysis Letters, 143(10): 1018–1024

    Article  CAS  Google Scholar 

  • Zhang X, Zhang X, Song L, Hou F, Yang Y, Wang Y, Liu N (2018). Enhanced catalytic performance for CO oxidation and preferential CO oxidation over CuO/CeO2 catalysts synthesized from metal organic framework: effects of preparation methods. International Journal of Hydrogen Energy, 43(39): 18279–18288

    Article  CAS  Google Scholar 

  • Zhao C, Hao Q, Zhang Q, Yan N, Liu J, Dou B, Bin F (2019). Catalytic self-sustained combustion of toluene and reaction pathway over CuxMn1−xCe0.75Zr0.25/TiO2 catalysts. Applied Catalysis A, General, 569:66–74

    Article  CAS  Google Scholar 

  • Zou H, Dong X, Lin W (2006). Selective CO oxidation in hydrogenrich gas over CuO/CeO2 catalysts. Applied Surface Science, 253(5): 2893–2898

    Article  CAS  Google Scholar 

  • Żukowski W, Berkowicz G (2019a). The combustion of liquids and low-density solids in a cenospheric fluidized bed. Combustion and Flame, 206: 476–489

    Article  Google Scholar 

  • Żukowski W, Berkowicz G (2019b). The combustion of polyolefins in inert and catalytic fluidised beds. Journal of Cleaner Production, 236:117663

    Article  Google Scholar 

Download references

Acknowledgements

We gratefully acknowledge the financial support from the National Natural Science Foundation of China (No. 52176141).

Author information

Authors and Affiliations

Authors

Corresponding authors

Correspondence to Feng Bin, Shaohua Wu or Hongpeng Xu.

Additional information

Highlights

• Catalytic combustion in fluidized bed realizes efficient heat and mass transfer.

• Catalytic combustion in fluidized bed reduces the lean combustion limits.

• Catalytic combustion and flame combustion can be coupled.

• The diffusion/kinetics limited reaction model is suitable for catalytic combustion.

Declaration of Competing Interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zhang, Z., Zhang, C., Liu, H. et al. Self-sustained catalytic combustion of CO enhanced by micro fluidized bed: stability operation, fluidization state and CFD simulation. Front. Environ. Sci. Eng. 17, 109 (2023). https://doi.org/10.1007/s11783-023-1709-x

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s11783-023-1709-x

Keywords

Navigation