Abstract
This article presents an experimental and numerical investigation on the strength and performance of intermediate length rack column sections with C-stitches under axial compression. The test program consisted of 10 axial concentric compression tests on columns with and without C-stitches under pin end conditions for two different geometric lengths. Finite element (FE) models were developed using commercial FE package ABAQUS considering material and geometric nonlinearities as well as initial geometric imperfections. The elastic buckling properties of the section were calculated using readily available linear elastic buckling analysis tools based on Generalized Beam Theory (GBT) and Finite Strip Method (FSM). Obtained FE results were compared with those obtained experimentally, and once verified the developed FE modeling technique was used to carry out a parametric study to examine changes in structural response due to variations in length, depth and spacing of C-stitches. Observed influences of C-stitches on the behavior and resistance of the considered columns were carefully analyzed, and key design aspects are presented herein.
Similar content being viewed by others
References
Dinis P B, Camotim D. Local/distortional/global mode interaction in simply supported cold-formed steel lipped channel columns. International Journal of Structural Stability and Dynamics, 2011, 11(5): 877–902
Zhou W, Jiang L. Distortional buckling of cold-formed lipped channel columns subjected to axial compression. Steel and Composite Structures, 2017, 23(3): 331–338
Zirakian T, Zhang J. Elastic distortional buckling of singly symmetric i-shaped flexural members with slender webs. International Journal of Structural Stability and Dynamics, 2012, 12(2): 359–376
Schafer B W. Local, distortional, and Euler buckling in thin walled columns. Journal of Structural Engineering, 2002, 128(3): 289–299
Biggs K A, Ramseyer C, Suhyun R, Kang T H K. Experimental testing of cold-formed built-up members in pure compression. Steel and Composite Structures, 2015, 18(6): 1331–1351
Hancock G J. Distortional buckling of steel storage rack column. Journal of Structural Engineering, 1985, 111(12): 2770–2783
Lau S C W, Hancock G J. Distortional buckling formulas for channel column. Journal of Structural Engineering, 1987, 113(5): 1063–1078
Lau S C W, Hancock G J. Inelastic buckling ofchannel columns in the distortional mode. Thin-walled Structures, 1990, 10(3): 59–84
Kwon Y B, Hancock G J. Tests of cold formed channel with local and distortional buckling. Journal of Structural Engineering, 1992, 117(7): 1786–1803
Davises J M, Jiang C. Design for Distortional buckling. Journal of Constructional Steel Research, 1998, 46: 174–175
Narayanan S, Mahendran M. Ultimate capacity of innovative cold-formed steel columns. Journal of Constructional Steel Research, 2003, 59(4): 489–508
Talikoti R S, Bajoria K M. New approach to improving distortional strength of intermediate length thin-walled open section columns. Electronic Journal of Structural Engineering, 2005, 5: 69–79
Veljkovic M, Johansson B. Thin-walled steel columns with partially closed cross-section: Tests and computer simulations. Journal of Constructional Steel Research, 2008, 64: 816–821
Anbarasu M, Sukumar S. Study on the effect of ties in the intermediate length cold formed steel (CFS) columns. Structural Engineering and Mechanics, 2013, 46(3): 323–335
Anbarasu M, Amali D, Sukumar S. New approach to improve the distortional strength of intermediate length web stiffened thin walled open columns. KSCE Journal of Civil Engineering, 2013, 17(7): 1720–1727
Anbarasu M, Sukumar S. Finite element based investigation of performance of intermediate length columns with lateral stiffeners. Arabian Journal for Science and Engineering, 2014, 39(10): 6907–6917
Anbarasu M, Sukumar S. Influence of spacers on ultimate strength of intermediate length thin walled columns. Steel and Composite Structures, 2014, 16(4): 437–454
Simulia Inc. ABAQUS: Version 6.7–5, 2008
Council of Standards Australia. AS/NZS 4600:2005, Standards Australia, Sydney, Australia and Standards New Zealand, Wellington, New Zealand, 2005
Gunalan S, Mahendran M. Improved design rules for fixed ended cold-formed steel columns subject to flexural-torsional buckling. Thin-walled Structures, 2013, 73: 1–17
Bebiano R, Silvestre N, Camotim D. GBTUL 2.0 β — Code for Buckling and Vibration Analysis of Thin-Walled Members. 2008
Schafer B W. CUFSM 3.12, Elastic Buckling Analysis of Thin-Walled Members by Finite Strip Analysis, 2006
Standards Australia. AS 1391–1991, Methods for Tensile Steel Structures, Testing of Metal. Sydney, 1991
Anbarasu M, Murugapandian G. Experimental study on distor-tional-global buckling mode interaction on thin-walled lipped channel. Materials and Structures, 2016, 49(4): 1433–1442
Yang D, Hancock G, Rasmussen K. Compression tests of cold-reduced high strength steel sections. II: Long columns. Journal of Structural Engineering, 2004, 130(11): 1782–1788
Piyawat K, Ramseyer C, Kang T H K. Development of an axial load capacity equation for doubly-symmetric built-up cold-formed sections. Journal of Structural Engineering, 2013, 139(12): 04013008
Young B, Ellobody E. Buckling analysis of cold-formed steel lipped angle columns. Journal of Structural Engineering, 2005, 131(10): 1570–1579
Schafer B W, Pekoz T. Computational modelling of cold-formed steel: characterizing geometric imperfections and residual stresses. Journal of Constructional Steel Research, 1998, 47: 193–210
Jeyaragan S, Mahendran M. Development and Validation of Finite Element Models of Back to Back Lite Steel Beams. Brisbane: Queensland University of Technology, 2009
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Anbarasu, M., Ashraf, M. Structural behavior of intermediate length cold-formed steel rack columns with C-stitches. Front. Struct. Civ. Eng. 13, 937–949 (2019). https://doi.org/10.1007/s11709-019-0528-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11709-019-0528-4