Abstract
The microstructure and tensile behavior of two Al-7 pct Si-Mg casting alloys, with magnesium contents of 0.4 and 0.7 pct, have been studied. Different microstructures were produced by varying the solidification rate and by modification with strontium. An extraction technique was used to determine the maximum size of the eutectic silicon flakes and particles. The eutectic Si particles in the unmodified alloys and, to a lesser extent, in the Sr-modified alloys are larger in the alloys with higher Mg content. Large Fe-rich π-phase (Al9FeMg3Si5) particles are formed in the 0.7 pct Mg alloys together with some smaller β-phase (Al5FeSi) plates; in contrast, only β-phase plates are observed in the 0.4 pct Mg alloys. The yield stress increases with the Mg content, although, at 0.7 pct Mg, it is less than expected, possibly because some of the Mg is lost to π-phase intermetallics. The tensile ductility is less in the higher Mg alloys, especially in the Sr-modified alloys, compared with the lower Mg alloys. The loss of ductility of the unmodified alloy seems to be caused by the larger Si particles, while the presence of large π-phase intermetallic particles accounts for the loss in ductility of the Sr-modified alloy.
Similar content being viewed by others
References
G.A. Edwards, K. Stiller, G.L. Dunlop, and M.J. Couper: Mater. Sci. Forum, 1996, vols. 217–222, pp. 713–8.
H.W. Zandbergen, S.J. Andersen, and J. Jansen: Science, 1997, vol. 277, pp. 1221–5.
R.C. Harris, S. Lipson, and H. Rosenthal: AFS Trans., 1956, vol. 64, pp. 470–81.
S.F. Frederick and W.A. Bailey: Trans. TMS-AIME, 1968, vol. 242, pp. 2063–7.
R. Sinfield and D.A. Harris: J. Aus. Inst. Met., 1975, vol. 20, pp. 44–8.
J.A. Eady and D.M. Smith: Mater. Forum, 1986, vol. 9, pp. 217–23.
S. Shivkumar, C. Keller, and D. Apelian: AFS Trans., 1990, vol. 98, pp. 905–10.
K.T. Kashyap, S. Murali, K.S. Raman, and K.S.S. Murthy: Mater. Sci. Technol., 1993, vol. 9, pp. 189–203.
S. Murali, K.S. Raman, and K.S.S. Murthy: Mater. Sci. Eng., 1992, vol. A151, pp. 1–10.
A.T. Joenoes and J.E. Gruzleski: Cast Met., 1991, vol. 4, pp. 62–71.
B. Closset and J.E. Gruzleski: Metall. Trans. A, 1982, vol. 13A, pp. 945–51.
G. Gustafsson, T. Thorvaldsson, and G.L. Dunlop: Metall. Trans. A, 1986, vol. 17A, pp. 45–52.
G.E. Nagel, J.P. Mouret, and J. Dubruelh: AFS Trans., 1983, vol. 91, pp. 157–60.
D.A. Granger, R.R. Sawtell, and M.M. Kersker: AFS Trans., 1984, vol. 92, pp. 579–86.
G.K. Sigworth, S. Shivkumar, and D. Apelian: AFS Trans., 1989, vol. 97, pp. 811–24.
Y.H. Tan, S.L. Lee, and Y.L. Lin: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 1195–205.
C. Verdu, H. Cercueil, S. Communal, P. Sainfort, and R. Fougeres: Mater. Sci. Forum, 1996, vols. 217–222, pp. 1449–54.
Q.G. Wang, C.H. Caceres, and J.R. Griffiths: AFS Trans., 1998, vol. 106, pp. 131–6.
Q.G. Wang and C.H. Caceres: Mater. Sci. Eng., 1997, vols. A234–A236, pp. 106–9.
Q.G. Wang and C.H. Caceres: Mater. Sci. Forum, 1996, vol. 242, pp. 159–64.
C.H. Caceres and B.I. Selling: Mater. Sci. Eng., 1996, vol. A220, pp. 109–16.
R.E. Spear and G.R. Gardner: AFS Trans., 1963, vol. 71, pp. 209–15.
D.L. McLellan: AFS Trans., 1982, vol. 90, pp. 173–91.
C.H. Caceres, C.J. Davidson, and J.R. Griffiths: Mater. Sci. Eng., 1995, vol. A197, pp. 171–9.
C.H. Caceres and Q.G. Wang: Int. J. Cast Met. Res., 1996, vol. 9, pp. 157–62.
J.C. Jaquet: 2nd Int. Conf. on Molten Aluminium Processing, AFS, Des Plaines, IL, 1989, pp. 2.1–2.36
C.H. Caceres and Q.G. Wang: AFS Trans., 1996, vol. 104, pp. 1039–43.
M.S. Misra and K.J. Oswalt: AFS Trans., 1982, vol. 90, pp. 1–10.
S. Shivkumar, S. Ricci, Jr., B. Steenhoff, D. Apelian, and G.K. Sigworth: AFS Trans., 1989, vol. 97, pp. 791–810.
D.S. Saunders, B.A. Parker, and J.R. Griffiths: J. Aus. Inst. Met., 1975, vol. 20, pp. 33–8.
R.W. Coade, S.M. Nugent, D.S. Saunders, J.R. Griffiths, and B.A. Parker: Proc. Annual Conf. of the Australasian Institute of Metals, Australasian Institute of Metals, Melbourne, 1977, pp. 6B-1–6B-2.
Q.G. Wang, C.H. Caceres, and J.R. Griffiths: Proc. 9th Int. Conf. on Fracture (ICF9), B.L. Karihaloo, Y.W. Mai, M.I. Ripley, and R.O. Ritchie, eds., Elsevier, London, 1997, pp. 2511–8.
Q.G. Wang and C.H. Caceres: Mater. Sci. Eng., 1998, vol. A241, pp. 72–82.
C.H. Caceres and J.R. Griffiths: Acta Mater., 1996, vol. 44, pp. 25–33.
K.J. Oswalt and M.S. Misra: AFS Trans., 1980, vol. 88, pp. 845–62.
R.S. Chappell, T.A. Hughes, and G. Pollard: Metallography, 1970, vol. 3, pp. 235–7.
E.E. Underwood: Quantitative Stereology, Addison-Wesley, Reading, MA, 1970.
C.J. Simensen and T.L. Rolfsen: Z. Metallkd., 1997, vol. 88, pp. 142–6.
J.M. Dowling and J.W. Martin: Acta Metall., 1976, vol. 24, pp. 1147–53.
A. Kelly: Phil. Mag., 1958, vol. 3, pp. 1472–4.
C.H. Caceres, C.J. Davidson, J.R. Griffiths, L.M. Hogan, and Q.G. Wang: Mater. Forum, 1997, vol. 21, pp. 27–43.
Aerospace Structural Metals Handbook, W. F. Brown, H. Mindlin, and C.Y. Ho, eds., CINDAS/USAF CRDA Handbooks Operation, Purdue University, West Lafayette, IN, 1959 (1995 revision, Figure 1.0918).
C.H. Caceres, J.R. Griffiths, and P. Reiner: Acta Mater., 1996, vol. 44, pp. 15–23.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Caceres, C.H., Davidson, C.J., Griffiths, J.R. et al. The effect of Mg on the microstructure and mechanical behavior of Al-Si-Mg casting alloys. Metall Mater Trans A 30, 2611–2618 (1999). https://doi.org/10.1007/s11661-999-0301-8
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-999-0301-8