Skip to main content
Log in

Comparisons between centrifuge and numerical modeling results for slope toppling failure

  • Article
  • Special Issue on Rock Fractures and Discontinuities: Modeling and Analysis
  • Published:
Science China Technological Sciences Aims and scope Submit manuscript

Abstract

This paper presents series studies on the toppling mechanism by centrifuge tests and numerical simulations. Two different discrete element methods, i.e., the continuum-based discrete element method (CDEM) and the discontinuous deformation analysis (DDA), are adopted. The modeling results show that both the methods can accurately capture the failure modes of the centrifuge tests, including three distinct zones and two failure surfaces. Comparisons are made between the physical test and numerical simulation results. The critical inclination angle of the tilting table where the slope models are fixed on can be moderately predicted by the two methods, with different degrees of precision. The error between the test results and the simulated results is within 1% for the slope models without rock-bridges by both CDEM and DDA. However, it is amplified for the staggered-joint models that simulate the rock-bridges. With DDA, the average error is about 5%, and the maximum error is up to 17%. While with CDEM, the errors for the aligned-joint models are ranged from 1% to 6%, and it is from 10% to 29% for the staggered- joint models. The two numerical methods show the capability in simulating toppling failure of blocky rock mass with and without rock-bridges. The model with rock-bridges which provides a certain bending resistance is more stable than the one without any rock-bridge. In addition, the two failure surfaces were observed, which is different from the common understanding that only one failure surface appears.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Whyter R J. A study of progressive hanging wall caving at Chambishi copper mine in Zambia using the base friction model concept. Dissertation of Master Degree. London: London University, 1973

    Google Scholar 

  2. Ashiby J. Sliding and toppling modes of failure in model and jointed rock slopes. Dissertation of Master Degree. London: Royal School of Mines, 1971

    Google Scholar 

  3. Hittinger M. Numerical analysis of toppling failure in jointed rock. Dissertation of Doctor Degree. Berkeley: University of California, 1978

    Google Scholar 

  4. Bray J W, Goodman R E. 1981. The theory of base friction models. Int J Rock Mech Min, 1981; 18: 453–468

    Article  Google Scholar 

  5. Adhikary D P, Dyskin A V, Jewell R J, et al. A study of mechanism of flexural topping failure of rock slopes. Rock Mech Rock Eng, 1997; 30: 75–93

    Article  Google Scholar 

  6. Zhang J H, Chen Z Y, Wang X G. Centrifuge modeling of rock slopes susceptible to block toppling. Rock Mech Rock Eng, 2007; 40: 363–382

    Article  Google Scholar 

  7. Pritchard M A, Savigny K W. Numerical modeling of toppling. Can Geotech J, 1990; 27: 824–834

    Google Scholar 

  8. Lanaro F, Jing L, Stephansson O, et al. D.E.M. modeling of laboratory tests of block toppling. Int J Rock Mech Min, 1997, 34: 173

    Article  Google Scholar 

  9. Barla G, Devin P, Zaninetti A. Validation of a distinct element model for toppling rock slopes. In: 8th ISRM Congress. Int. Cong, on Rock Mechanics of Int. Society for Rock Mechanics, Tokyo, 1995; 3: 417–421

    Google Scholar 

  10. Nichol S L, Hungr O, Evans S G. Large-scale brittle and ductile toppling of rock slopes. Can Geotech J, 2002; 39: 773–788

    Article  Google Scholar 

  11. Goricki A, Goodman R E. Failure models of rock slopes demonstrated with base friction and simple numerical models. Felsbau, 2003; 21: 8–12

    Google Scholar 

  12. Koo C Y, Chern J C. Modification of the DDA method for rigid block problems. I Int J Rock Mech Min, 1998; 35: 683–693

    Article  Google Scholar 

  13. Wu J H, Ohnishi Y Z, Shi G H, et al. Theory of three-dimensional discontinuous deformation analysis and its application to a slope toppling at Amatoribashi, Japan. Int J Geomec ASCE, 2005; 5: 179–195

    Article  Google Scholar 

  14. Shi G H. Applications of Discontinuous Deformation Analysis (DDA) to Rock Engineering. Beijing: Tsinghua University Press & Springer, 2007. 136–147

    Google Scholar 

  15. Alzo’ubi A K, Martin C D, Cruden D M. Influence of tensile strength on toppling failure in centrifuge tests. Int J Rock Mech Min, 2010; 47: 974–982

    Article  Google Scholar 

  16. Gu J, Zhao Z Y. Considerations of the discontinuous deformation analysis on wave propagation. Int J Numer Anal Meth Geomech, 2009; 33: 1449–1465

    Article  MATH  Google Scholar 

  17. Scholtès L, Donzé F V. Modeling progressive failure in fratured rock masses using a 3D discrete element method. Int J Rock Mech Min, 2012; 52: 18–30

    Article  Google Scholar 

  18. Ning Y J, Yang J, An X M, et al. Modeling rock fracturing and blast-induced rock mass failure via advanced discretisation within the discontinuous deformation analysis framework. Comput Geotech, 2011; 38: 40–49

    Article  Google Scholar 

  19. Eberhardt E, Stead D, Coggan J S. Numerical analysis of initiation and progressive failure in natural rock slopes–the 1991 Randa rockslide. Int J Rock Mech Min, 2004; 41: 69–87

    Article  Google Scholar 

  20. Zhang G X, Zhao Y, Peng X C. Simulation of toppling failure of rock slope by numerical manifold method. Int Comput Method, 2010; 7: 167–189

    Article  Google Scholar 

  21. Feng C, Li S, Liu X, et al. A semi-spring and semi-edge combined contact model in CDEM and its application to analysis of Jiweishan landslide. J Rock Mech Geotec Eng, 2014; 6: 26–35

    Article  Google Scholar 

  22. Schofield A N. Cambridge geotechnical centrifuge operations. Géotechnique, 1980; 30: 227–268

    Article  Google Scholar 

  23. Kutter B L, Moquette L, Thompson P Y. Gravity-scaled tests on blast-induced soil-structure interaction. J Geotec Eng, 1988; 114: 431–447

    Article  Google Scholar 

  24. Chen Z Y, Zhang J H, Wang W X, et al. Centrifuge modeling for rock slopes. In: Ng C, Zhang L M, Wang Y H, eds. Proceedings of the Sixth International Conference Physical Modelling Geotechnics, Hong kong, London: Taylor & Francis Group, 2006. 19–28

  25. Li S H, Zhao M H, Wang Y N, et al. A new numerical method for DEM-block and particle model. Int J Rock Mech Min, 2004; 41: 414–418

    Article  Google Scholar 

  26. Ma Z S, Feng C, Liu T P, et al. A GPU accelerated continuousbaseddiscrete element method for elasto dynamics analysis. Adv Mater Res, 2011; 320: 329–334

    Article  Google Scholar 

  27. Wang J, Li S H, Feng C. A shrunken edge algorithm for contact detection between convex polyhedral blocks. Comput Geotech, 2015; 63: 315–330

    Article  Google Scholar 

  28. Shi G H. Discontinuous deformation analysis-Anew model for the statics and dynamics of block systems. Dissertation of Doctor Degree. Berkeley: University of California, 1988

    Google Scholar 

  29. Shi G H. Simplex integration for manifold method and discontinuous deformation analysis. In: Working Forum on the Manifold Method of Material Analysis, Chungli, Taiwan, 1995. 2, 129–164

    Google Scholar 

  30. Jing L. Formulation of discontinuous deformation analysis (DDA)—animplicit discrete element model for block systems. Eng Geol, 1998; 49: 371–381

    Article  Google Scholar 

  31. Jing L. A review of techniques, advances and outstanding issues in numerical modeling fro rock mechanics and rock engineering. Int J Rock Mech Min, 2003; 40: 285–353

    Article  Google Scholar 

  32. Dooling D M, Sitar N. Time integration in discontinuous deformation analysis. J Eng Mech-ASCE, 2004; 130: 249–259

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to WenJun Gong.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Chen, Z., Gong, W., Ma, G. et al. Comparisons between centrifuge and numerical modeling results for slope toppling failure. Sci. China Technol. Sci. 58, 1497–1508 (2015). https://doi.org/10.1007/s11431-015-5889-x

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11431-015-5889-x

Keywords

Navigation