Abstract
The seismic performance of two RC interior wide beam-column connections representative of existing frames designed and detailed according to past construction practices in the moderate-seismicity Mediterranean area was investigated experimentally. The specimens were subjected to axial loads, moderate levels of gravity loading and cyclic displacements up to failure. The specimens exhibited a “strong column-weak beam” type of flexural yielding mechanism. The wide beams did not reach the expected capacities corresponding to the formation of a full-width plastic hinge. The wide-beam longitudinal bars exhibited significant slippage, and the transverse beams underwent severe torsion cracking and even failure; this caused severe pinching in the load versus displacement hysteretic loops and exacerbated the intrinsic flexibility of this type of connection. The average drift ratios at first yielding of the wide beam longitudinal reinforcement and at failure were 2.7 and 4.5%, respectively. The displacement ductility ratio was about 2.8. The ultimate energy dissipation capacity of each specimen—obtained by dividing the total plastic strain energy by the product of the yield load and yield displacement—was approximately 9, which is about one fourth of the value recommended for providing adequate seismic performance. Finally, a simple approach is suggested for prediction of the bending capacity of existing connections.
Similar content being viewed by others
References
ACI (1995). Building Code Requirements for Structural Concrete (ACI318-95) and Commentary (ACI318R-95). American Concrete Institute Committee 318, Farmington Hills, MI
ACI (1999). Building Code Requirements for Structural Concrete (ACI318-99) and Commentary (ACI318R-99). American Concrete Institute Committee 318, Farmington Hills, MI
ACI (2005). Building Code Requirements for Structural Concrete (ACI318-05) and Commentary (ACI318R-05). American Concrete Institute Committee 318, Farmington Hills, MI
ACI (2008). Building Code Requirements for Structural Concrete (ACI318-08) and Commentary (ACI318R-08). American Concrete Institute Committee 318, Farmington Hills, MI
ACI-ASCE (1991). Recommendations for Design of Beam-Column Joints in Monolithic Reinforced Concrete Structures. American Concrete Institute Committee 352, Farmington Hills, MI
Bakir PG (2003). Seismic resistance and mechanical behaviour of exterior beam-column joints with crossed inclined bars. Struct Eng Mech Int J 16(4): 493–517
Bakir PG and Boduroglu HM (2006). Nonlinear analysis of beam-column joints using softened truss model. Mech Res Commun 33(2): 134–147
Benavent-Climent A (2007). Seismic behavior of RC wide beam-column connections under dynamic loading. J Earthq Eng 11: 493–511
Bonacci J and Pantazopoulou S (1993). Parametric investigation of joint mechanisms. ACI Struct J 90(1): 61–71
CDCC (1991). Instrucción para el proyecto y la ejecución de obras de hormigón en masa o armado. Committee for the development of concrete codes of the Spanish Ministry of Construction, Madrid
CDSC (1974). Norma Sismorresistente PDS-1 Parte A. Committee for the development of seismic codes of the Spanish Ministry of Construction, Madrid
CDSC (1994). Norma de Construcción Sismorresistente NCSE-94. Committee for the development of seismic codes of the Spanish Ministry of Construction, Madrid
CDSC (2002). Norma de Construcción Sismorresistente NCSE-02. Committee for the development of seismic codes of the Spanish Ministry of Construction, Madrid
Darwin D and Nmai CK (1986). Energy dissipation in RC beams under cyclic load. J Struct Eng 112(8): 1829–1846
Ehsani MR and Wight JK (1985). Effect of transverse beams and slab on behaviour of reinforced concrete beam-to-column connections. ACI J 82(2): 185–195
EN 1998-1 (2004). Eurocode 8: design of structures for earthquake resistance—part 1: general rules, seismic actions and rules for buildings. European Committee for Standardization, Brussels
Gentry RG and Wight JK (1994). Wide beam-column connections under earthquake-type loading. Earthq Spectra 10: 675–703
Hatamoto H, Bessho S and Shibata T (1991). Reinforced concrete wide-beam to column subassemblages subjected to lateral loads. In: Jirsa, J (eds) Design of Beam-Column Joints for Seismic Resistance ACI Publication SP-123, pp 291–316. American Concrete Institute, Detroit Michigan
Ichinose T (1991) Interaction between bond at beam bars and shear reinforcement in RC interior joints. Design of beam-column joints for seismic resistance, SP-123, American Concrete Institute, Farmington Hills, Michigan, pp 379–400
Kim J and LaFave JM (2007). Key influence parameters for the joint shear behaviour of reinforced concrete beam-column connections. Eng Struct 29(10): 523–539
Leon RT (1991). Towards new bond and anchorage provisions for interior joints. In: Jirsa, J (eds) Design of Beam-Column Joints for Seismic Resistance ACI Publication SP-123, pp 425–442. American Concrete Institute, Detroit, Michigan
NZSA (1995). Standard for the Design of Concrete Structures (NZS3101-95). New Zealand Standards Authority, New Zealand
Paulay T, Park R (1984) Joints in reinforced concrete frames designed for earthquake resistance. Research report 84–9, Department of Civil Engineering, University of Canterbury, Christchurch, New Zealand
Paulay T (1989). Equilibrium criteria for reinforced concrete beam-column joints. ACI Struct J 86(6): 635–643
Popov EP, Cohen E, Koso-Thomas K and Kasai K (1992). Behavior of interior narrow and wide beams. ACI Struct J 89(6): 607–616
Quintero-Febres CG and Wight JK (2001). Experimental study of reinforced concrete interior wide beam-column connections subjected to lateral loading. ACI Struct J 98(4): 572–582
Scribner CF and Wight JK (1980). Strength decay in reinforced concrete members under load reversals. J Struct Div ASCE 106(4): 861–875
Siah WL, Stehle JS and Goldsworthy H (2003). Interior wide beam connections subjected to lateral earthquake loading. Eng Struct 25: 281–291
Sugano S (1968) Study on inelastic stiffness of reinforced concrete structures. Research Reports of the Annual Meeting. Architectural Institute of Japan Kanto Branch, Tokyo
Vollum RL and Newman JB (1999). Strut and tie models for analysis/design of external beam-column joints. Mag Concrete Res 51(6): 415–425
Vollum R and Parker D (2008). External beam-column joints: design to eurocode 2. Mag Concrete Res 60(7): 511–521
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Benavent-Climent, A., Cahís, X. & Vico, J.M. Interior wide beam-column connections in existing RC frames subjected to lateral earthquake loading. Bull Earthquake Eng 8, 401–420 (2010). https://doi.org/10.1007/s10518-009-9144-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10518-009-9144-3