Skip to main content

Advertisement

SpringerLink
Log in

Effects of the viscosity and thermal property of fluids on the residual wall thickness and concentricity of the hollow products in fluid-assisted injection molding

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Water-assisted injection molding (WAIM) is a method of producing plastic products with hollow internal sections. The flow instability and boiling effect of the water cause non-uniform residual wall thickness (RWT) and void in the wall in WAIM. Due to the high heat capacity and thermal conductivity of the water, the RWT is affected by the viscosity change of injected plastics when the hollow sections are formed. In this study, the effects of process parameters on the distribution of the RWT and the concentricity of the hollow sections in the products with amorphous ABS (Acrylonitrile Butadiene Styrene: amorphous polymer) and crystalline PP (Polypropylene: semi-crystalline polymer) were compared, and the water (0.86 mPa · s @ 25 °C) and high viscosity silicone oil (970 mPa · s @ 25 °C) were used as the secondary injection fluids in the experiments. The RWT was more stable, with the silicone oil having higher viscosity and boiling point compared to the water. The capillary number which could decide the shape of the flow front was also affected by the viscosity of the fluids. Due to the higher capillary number of the silicone oil, the flow front was formed with narrow and long elliptical shape. The higher capillary number also caused the stable flow of the flow front, resulting in stable RWT with the silicone oil. The concentricity of the hollow sections was higher with the silicone oil than with the water.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Menges G, Michaeli W, Mohren P (2000) How to make injection molds. Hanser, NY

    Google Scholar 

  2. Heim HP, Potente H (2001) Specialized molding techniques. Plastics Design Library, NY

    Google Scholar 

  3. Mikell K (2002) Water injection molding makes hollow parts faster. Plast Technol 48(4):42–47

    Google Scholar 

  4. Mapleston P (2001) Injection molding water-assisted process shows promise. Mod Plast 31:33–33

  5. Michaeli W, Brunswick A, Kujat C (2000) Reducing cooling time with water-assisted injection molding. Kunst Plast Eur 90:25–27

    Google Scholar 

  6. Sannen S, Keyzer J, Puyvelde P (2014) Formation of part defects in water-assisted injection molding(WAIM): influence of process and material parameters. Proc ANTEC 2014:1557–1564

    Google Scholar 

  7. Yang S, Chou H (2002) Study on the residual wall thickness at dimensional transitions and curved sections in gas-assisted molded circular tubes. Polym Eng Sci 42(1):111–119

    Article  MathSciNet  Google Scholar 

  8. Lin Y, Chang FA, Liu SJ (2009) Using differential mold temperatures to improve the residual wall thickness uniformity around curved sections of fluid assisted injection molded tubes. Int Commun Heat Mass Transfer 36:491–497

    Article  Google Scholar 

  9. Liu SJ, Lin MJ, Wu YC (2007) An experimental study of the water-assisted injection molding of glass fiber filled poly-butylene-terephthalate(PBT) composites. Compos Sci Technol 67:1415–1424

    Article  Google Scholar 

  10. Liu SJ, Chen WK (2004) Experimental investigation and numerical simulation of cooling process in water assisted injection moulded parts. Plast Rubber Compos 33(6):260–266

    Article  Google Scholar 

  11. Liu SJ, LIN SP (2006) Factors affecting the formation of fingering in water assisted injection molded thermoplastics. Adv Polym Technol 25(2):98–108

    Article  Google Scholar 

  12. Olley JP, Coates PD (2000) Gas-assisted injection moulding finite element modelling and experimental validation. Plast Rubber Compos 29:31–37

    Article  Google Scholar 

  13. Polynkin A, Pittman J, Sienz J (2005) 3-D simulation of gas-assisted injection moulding: analysis of primary and secondary gas penetration and comparison with experimental results. Int Polym Process 20:191–210

    Article  Google Scholar 

  14. Polynkin A, Pittman J, Sienz J (2005) Gas-assisted injection moulding of a handle: three dimensional simulation and experimental verification. Polym Eng Sci 45:1049–1058

    Article  Google Scholar 

  15. Polynkin A, Pittman J, Sienz J (2005) Industrial applications of gas-assisted injection moulding: numerical prediction and experimental trails. Plast Rubber Compos 34:236–246

    Article  Google Scholar 

  16. Goodship V (2002) Multi-material injection moulding. Rapra Technology, Shrewsbury

    Google Scholar 

  17. Donovan RC, Rabe KS, Mammel WK, Lord HA (1975) Recycling plastics by two-shot molding. Polym Eng Sci 15(11):774–780

    Article  Google Scholar 

  18. White J, Lee B (1975) An experimental study of sandwich injection molding of two polymer melts using simultaneous injection. Polym Eng Sci 15(7):481–485

    Article  Google Scholar 

  19. Young S, White J, Clark E, Oyanagi Y (1980) A basic experimental study of sandwich injection molding with sequential injection. Polym Eng Sci 20(12):798–804

    Article  Google Scholar 

  20. Turng L, Wang V, Wang K (1993) Numerical simulation of co-injection molding process. J Eng Mater Technol 115:48–53

    Article  Google Scholar 

  21. Moon JS (1999) A study on multi-component injection molding by finite element method. PhD-thesis, Seoul National University, Seoul, Korea

  22. Schlatter G, Agassant J, Vincent M, Davidoff A (1999) An unsteady multifluid flow model: application to sandwich injection molding process. Polym Eng Sci 39(1):78–88

    Article  Google Scholar 

  23. Yang W, Yokoi H (2003) Visual analysis of the flow behavior of core material in a fork portion of plastic sandwich injection molding. Polym Test 22:37–43

    Article  Google Scholar 

  24. Ilinca F, Hetu J, Derdouri A (2006) Numerical investigation of the flow front behavior in the co-injection moulding process. Int J Numer Methods Fluids 50:1445–1460

    Article  MATH  Google Scholar 

  25. Polynkin A, Bai L, Pittman J, Sienz J, Mulvaney-Johnson L, Brown E, Dawson A, Coates P, Brookshaw B, Vinning K, Butler J (2008) Water assisted injection moulding: development of insights and predictive capabilities through experiments on instrumented process in parallel with computer simulations. Plast Rubber Compos 37(2–4):131–141

    Article  Google Scholar 

  26. Jo ES (1996) An experimental study on two-phase flow characteristics in gas-injected hele-shaw cells. Phd-Thesis, Seoul National University, Seoul, Korea

  27. Baeg G (1998) A study on two-phase flow characteristics by gas injection into liquid in a hele-shaw cell. Master-Thesis, Seoul National University, Seoul, Korea

  28. Baeg S (2000) A study on the characteristics of two-phase flow in a gas-injected capillary tube. Master-Thesis, Seoul National University, Seoul, Korea

  29. Polynkin A, Pittman J, Sienz J (2004) Gas displacing liquids from tubes: high capillary number flow of a power law liquid including inertia effects. Chem Eng Sci 50:2969–2982

    Article  Google Scholar 

  30. Thompson R, Soares E (2012) Motion of a power-law long drop in a capillary tube filled by a Newtonian fluid. Chem Eng Sci 72:126–141

    Article  Google Scholar 

  31. Yang J, Zhou X (2012) Numerical simulation on residual wall thickness of tubes with dimensional transitions and curved sections in water assisted injection molding. Polym Eng Sci. doi:10.1002/app.38394

    Google Scholar 

  32. Park H, Cha B, Park S, Choi J, Kim D, Rhee B, Lee K (2014) A study on void formation in the residual wall thickness of a curved area during fluid-assisted injection molding. Proc ANTEC 2014:1717–1720

    Google Scholar 

  33. Huang HX, Deng ZW (2008) Effects and optimization of processing parameters in water-assisted injection molding. J Appl Polym Sci 108:228–235

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Mold Technology Team, Hyundai Mobis, 460-30 Sam-dong, Uiwang-si, Gyeonggi-do, 437-040, Republic of Korea

    Hyungpil Park

  2. Department of Mechanical Engineering, Ajou University, San 5, Woncheon-Dong, Yeongtong-Gu, Suwon, Kyungki-Do, 443-749, South Korea

    Byungohk Rhee

Authors
  1. Hyungpil Park
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Byungohk Rhee
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Hyungpil Park.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Park, H., Rhee, B. Effects of the viscosity and thermal property of fluids on the residual wall thickness and concentricity of the hollow products in fluid-assisted injection molding. Int J Adv Manuf Technol 86, 3255–3265 (2016). https://doi.org/10.1007/s00170-016-8423-9

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-016-8423-9

Keywords

Search

Navigation