Skip to main content
SpringerLink
Log in

Assessment of surface integrity of Ni superalloy after electrical-discharge, laser and mechanical micro-drilling processes

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Currently, electrical discharge machining (EDM) is the established manufacturing process for making holes through Ni superalloy turbine blades to facilitate blade cooling. Surface integrity of these sub-millimetre holes is of paramount importance since it directly influences the fatigue life of the component. In this paper, EDM is compared against laser and mechanical micro-hole drilling of Inconel 718 alloy. The motivation was to assess alternative manufacturing methods for raising the quality threshold of micro-drilled holes. Mechanical and metallurgical characterisation of surface and subsurface regions of the holes produced by the three processes was undertaken using backscatter electron (BSE) microscopy, electron backscatter diffraction (EBSD) and nano-indentation techniques to assess surface hardness, grain misorientation, plastic deformation and the heat-affected zone. The results suggest that mechanical micro-drilling offers improved mechanical, metallurgical and geometrical properties compared to both laser and EDM processes.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Bradbury SR, Huyanan T (2000) Challenges facing surface engineering technologies in the cutting tool industry. Vacuum 56(3):173–177

    Article  Google Scholar 

  2. Stephen L, Kursad S, Lin L, Clive G-R, Martyn C (2009) Statistical analysis of recast formation in laser drilled acute blind holes in CMSX-4 nickel superalloy. Int J Adv Manuf Technol 43:1094–1105

    Article  Google Scholar 

  3. Thao O, Joshi SS (2008) Analysis of heat affected zone in the micro-electric discharge machining. Int J Manuf Technol Manag 13(2/3/4):201–213

    Google Scholar 

  4. Newton TR, Melkote SN, Watkins TR, Trejo RM, Reister L (2009) Investigation of the effect of process parameters on the formation and characteristics of recast layer in wire-EDM of Inconel 718. Mater Sci Eng A 513–514:208–215

    Article  Google Scholar 

  5. Aspinwall DK, Soo SL, Berrisford AE, Walder G (2008) Workpiece surface roughness and integrity after WEDM of Ti–6Al–4 V and Inconel 718 using minimum damage generator technology. CIRP Ann Manuf Technol 57:187–190

    Article  Google Scholar 

  6. Bleys P, Kruth J-P, Lauwers B, Schacht B, Balasubramanian V, Froyen L, van Humbeeck J (2006) Surface and sub-surface quality of steel after EDM. Adv Eng Mater 8(1–2):15–25

    Article  Google Scholar 

  7. Field M, Kahles JF, Koster WP (1966) The surface effects produced in nonconventional metal removal- comparison with conventional machining techniques. Met Eng Q Am Soc Met 6:32–45

    Google Scholar 

  8. Tolinski M (2006) Smaller holes-bigger challenges: holemaking in tough materials serves more demanding aircraft. Manuf Eng 136(3):95–108

    Google Scholar 

  9. Salkind M (1989) Aerospace materials research opportunities. Angewandte Chemie. Int Ed Engl 28(5):655–662

    Article  Google Scholar 

  10. Serebryakov VA, Volkov MV, Zhang X (2005) Laser drilling of microholes in refractory alloys. J Opt Technol 72(3):241–244

    Article  Google Scholar 

  11. Dubey AK, Yadava V (2008) Laser beam machining- a review. Int J Mach Tools Manuf 48:609–628

    Article  Google Scholar 

  12. Bandyopadhyay S, Sarin Sundar JK, Sundararajan G, Joshi SV (2002) Geometrical features and metallurgical characteristics of Nd:YAG laser drilled holes in thick IN 718 and Ti-6Al-4 V sheets. J Mater Process Technol 127:83–95

    Article  Google Scholar 

  13. Chien W-T, Hou S-C (2007) Investigation the recast layer formed during laser trepan drilling of Inconel 718 using Taguchi method. Inter J Adv Manuf Technol 33:308–316

    Article  Google Scholar 

  14. Sezer HK, Li L, Schmidt M, Pinkerton AJ, Anderson B, Williams P (2006) Effect of beam angle on HAZ, recast and oxide layer characteristics in laser drilling of TBC nickel superalloys. Int J Mach Tools Manuf 46:1972–1982

    Article  Google Scholar 

  15. Allan D, Almond H, Logan P (2000) A technical comparison of micro-electrodischarge machining, microdrilling and copper vapour laser machining for the fabrication of ink jet nozzles. Proc SPIE 4019:531–540

    Article  Google Scholar 

  16. Ion JC (2005) Laser processing of engineering materials: principles, procedure and industrial application. Elsevier Butterworth-Heinemann

  17. Zhang JH, Lee TC, Ai X, Lau WS (1996) Investigation of the surface integrity of laser cut ceramic. J Mater Process Technol 57:304–310

    Article  Google Scholar 

  18. Feifer A (1989) Drilling micro-size deep holes. Tool Prod 55(7):1–2

    Google Scholar 

  19. Sharman ARC, Amarashighe A, Ridgway K (2008) Tool life and surface integrity aspects when drilling and hole making in Inconel 718. J Mater Process Technol 200(1):424–432

    Article  Google Scholar 

  20. Kwong J, Axinte DA, Withers PJ (2009) The sensitivity of Ni-based superalloy to hole making operations: influence of process parameters on subsurface damage and residual stress. J Mater Process Technol 209(8):3968–3977

    Article  Google Scholar 

  21. Rahim E, Sasahara H (2009) Application of minimum quantity lubrication when drilling nickel-based superalloy at high cutting speed. Key Eng Mater 407:612–615

    Article  Google Scholar 

  22. Axinte DA, Andrews P (2007) Some considerations on tool wear and workpiece surface quality of holes finished by reaming or milling in a nickel base superalloy. Proc Inst Mech Eng B J Eng Manuf 221(4):591–603

    Article  Google Scholar 

  23. Imran M, Mativenga PT, Gholinia A, Withers PJ (2010) Evaluation of the surface integrity in micro drilling process for nickel based superalloy. Int J Adv Manuf Technol. Published online on Dec. 23, 2010

  24. Imran M, Mativenga PT, Gholinia A, Withers PJ (2014) Comparison of tool wear mechanisms and surface integrity for dry and wet micro-drilling of nickel base superalloys. Int J Mach Tools Manuf 76:49–60

    Article  Google Scholar 

  25. Lee K, Dornfeld DA (2005) Micro-burr formation and minimization through process control. Precis Eng 29(2):246–252

    Article  Google Scholar 

  26. Imran M, Mativenga PT, Kannan S (2010) An investigation into the effects of tool geometry in micro drilling process for nickel based superalloy. The 5th International Conference on Micro-Manufacturing ICOMM / 4 M, Madison, 85 - 93 April 5-8

  27. Imran M (2010) Feasibility and process development of mechanical micro drilling for nickel based super alloys. PhD thesis, The University of Manchester, U.K

  28. Masuzawa T (2000) State of the art of micromachining. CIRP Ann Manuf Technol 49(2):473–488

    Article  Google Scholar 

  29. Jaffery SI, Khan M, Ali L, Mativenga PT (2014) Statistical analysis of process parameters in micromachining of Ti-6Al-4 V alloy. Proc IMechE B J Eng Manuf. doi:10.1177/0954405414564409

    Google Scholar 

  30. Okasha MM, Mativenga PT, Driver N, Li L (2010) Sequential laser and mechanical micro-drilling of Ni superalloy for aerospace application. CIRP Ann Manuf Technol 59(1):199–202

    Article  Google Scholar 

  31. Kuppan P, Rajadurai A, Narayanan S (2008) Influence of EDM process parameters in deep hole drilling of Inconel 718. Int J Adv Manuf Technol 38:74–84

    Article  Google Scholar 

  32. Imran M, Mativenga PT, Kannan S, Novovic D (2008) An experimental investigation of deep-hole microdrilling capability for a nickel-based superalloy. Proc Inst Mech Eng B J Eng Manuf 222(12):1589–1596

    Article  Google Scholar 

  33. Imran M, Mativenga PT, Withers PJ (2012) Assessment of machining performance using wear map approach in micro-drilling. Int J Adv Manuf Technol 59(1–4):119–126

    Article  Google Scholar 

  34. Mustafa A, Ulas C, Hascalik A (2013) Optimization of micro-EDM drilling of inconel 718. Int J Adv ManufTechnol 66:1015–1023

    Article  Google Scholar 

  35. Imran M, Mativenga PT, Gholinia A, Withers PJ (2011) Evaluation of the surface integrity in micro drilling process for nickel based superalloy. Int J Adv Manuf Technol 55(5–8):465–476

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Manufacturing and Laser Processing Research Group, School of Mechanical, Aerospace and Civil Engineering, The University of Manchester, Sackville St, Manchester, M13 9PL, UK

    M. Imran & P. T. Mativenga

  2. School of Materials, The University of Manchester, Grosvenor St, Manchester, M1 7HS, UK

    A. Gholinia & P. J. Withers

Authors
  1. M. Imran
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. P. T. Mativenga
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. Gholinia
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. P. J. Withers
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to M. Imran.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Imran, M., Mativenga, P.T., Gholinia, A. et al. Assessment of surface integrity of Ni superalloy after electrical-discharge, laser and mechanical micro-drilling processes. Int J Adv Manuf Technol 79, 1303–1311 (2015). https://doi.org/10.1007/s00170-015-6909-5

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-015-6909-5

Keywords

Search

Navigation