Abstract
Cellulose filament (CF) was modified via hybridization with poly (N-isopropylacrylamide-co-acrylic acid), which was prepared by free radical copolymerization of two monomers: N-isopropylacrylamide (NIPAM) as the thermosensitive component and acrylic acid (AAc) as the pH sensitive component. The copolymer was characterized with scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), and colloid tritation measurements. SEM and AFM images indicated the formation of semi-interpenetrating network (S-IPN) structure between cellulose filaments and poly(NIPAM-co-AAc). FTIR spectra displayed the characteristic peaks for CF and poly(NIPAM-co-AAc). TGA suggested that there was no degradation occurred for cellulose, and physical crosslinks between cellulose and poly(NIPAM-co-AAc) might be formed in the S-IPN. The amount of negative charges of CF/poly(NIPAM-co-AAc) was about 14.6 times that of neat CF. The adsorption of MV on CF/poly(NIPAM-co-AAc) reflected pH-dependence and pH 7.0 was the optimum pH value for MV adsorption. Adsorption isotherms at 293, 313 and 333 K could be described by Langmuir, Freundlich, Temkin and Sips models, amongst which Langmuir model had the best R2 values. At 293 K, the maximum adsorption capacity of S-IPN hybrids was 226.02 mg/g, which was higher than that of neat CF (64.83 mg/g). The negative values of ΔG0 and positive values ΔH0 calculated through thermodynamics equation indicated that the adsorption towards MV was a spontaneous and endothermic process. The adsorption kinetics followed a pseudo-second-order model and exhibited a three-stage intra-particle diffusion mode. The S-IPN hydrogels showed an increased desorption rate and an accelerated desorption process when temperature was increased. Furthermore, the S-IPN hydrogels showed that the desorption of MV was promoted by increasing temperature. Finally, the regenerated hydrogels reserved an adsorption capacity superior to that of the regenerated CF.
Similar content being viewed by others
References
Hameed BH, El-Khaiary MI (2008) Batch removal of malachite green from aqueous solutions by adsorption on oil palm trunk fibre: equilibrium isotherms and kinetic studies. J Hazard Mater 154:237–244
Thangamani KS, Sathishkumar M, Sameena Y, Vennilamani N, Kadirvelu K, Pattabhi S, Yun SE (2007) Utilization of modified silk cotton hull waste as an adsorbent for the removal of textile dye (reactive blue MR) from aqueous solution. Bioresour Technol 98:1265–1269
Moussavi G, Khosravi R (2011) The removal of cationic dyes from aqueous solutions by adsorption onto pistachio hull waste. Chem Eng Res Des 89:2182–2189
Kaşgöz H, Durmus A (2010) Dye removal by a novel hydrogel-clay nanocomposite with enhanced swelling properties. Polym Adv Technol 19:838–845
Gupta VK (2009) Suhas, Application of low-cost adsorbents for dye removal—a review. J Environ Manage 90:2313–2342
Jiang F, Dinh DM, Hsieh YL (2017) Adsorption and desorption of cationic malachite green dye on cellulose nanofibril aerogels. Carbohyd Polym 173:286–294
Garg VK, Kumar R, Gupta R (2004) Removal of malachite green dye from aqueous solution by adsorption using agro-industry waste: a case study of Prosopis cineraria. Dyes Pigm 62:1–10
Kang H, Liu R, Huang Y (2015) Graft modification of cellulose: methods, properties and applications. Polymer 70:A1–A16
Yang Z, Li H, Li A, Cheng T, Haijiang R (2013) Effect of hydrolysis degree of hydrolyzed polyacrylamide grafted; carboxymethyl cellulose on dye removal efficiency. Cellulose 20:2605–2614
Zhang M, Ding C, Huang L, Chen L, Yang H (2014) Interactions of collagen and cellulose in their blends with 1-ethyl-3-methylimidazolium acetate as solvent. Cellulose 21:3311–3322
O’Connell DW, Birkinshaw C, O’Dwyer TF (2008) Heavy metal adsorbents prepared from the modification of cellulose: a review. Bioresour Technol 99:6709–6724
Biswas A, Kim S, Selling GW, Cheng HN (2014) Conversion of agricultural residues to carboxymethylcellulose and carboxymethylcellulose acetate. Ind Crops Prod 60:259–265
Wang L, Li J (2013) Adsorption of C.I. Reactive Red 228 dye from aqueous solution by modified cellulose from flax shive: kinetics, equilibrium, and thermodynamics. Ind Crops Prod 42:153–158
Roman MJ, Decker EA, Goddard JM (2014) Fourier transform infrared studies on the dissociation behavior of metal-chelating polyelectrolyte brushes. ACS Appl Mater Interfaces 6:5383–5387
Bastakoti BP, Guragain S, Nakashima K, Yamauchi Y (2015) Stimuli-induced core-corona inversion of Micelle of poly(acrylic acid)-block-poly(N-isopropylacrylamide) and its application in drug delivery. Macromol Chem Phys 216:287–291
Wang F, Pan Y, Cai P, Guo T, Xiao H (2017) Single and binary adsorption of heavy metal ions from aqueous solutions using sugarcane cellulose-based adsorbent. Bioresour Technol 241:482–490
Wang Y, Wang W, Wang A (2013) Efficient adsorption of methylene blue on an alginate-based nanocomposite hydrogel enhanced by organo-illite/smectite clay. Chem Eng J 228:132–139
Dragan ES, Loghin DFA (2013) Enhanced sorption of methylene blue from aqueous solutions by semi-IPN composite cryogels with anionically modified potato starch entrapped in PAAm matrix. Chem Eng J 234:211–222
Karim Z, Mathew AP, Grahn M, Mouzon J, Oksman K (2014) Nanoporous membranes with cellulose nanocrystals as functional entity in chitosan: removal of dyes from water. Carbohydr Polym 112:668–676
Zhang M, Ding C, Chen L, Huang L, Yang H (2014) Tannin-immobilized collagen/cellulose bead as an effective adsorbent for Cu(II) in aqueous solutions. J Biobased Mater Bioenergy 8:610–617
Fan L, Luo C, Sun M, Li X, Lu F, Qiu H (2012) Preparation of novel magnetic chitosan/graphene oxide composite as effective adsorbents toward methylene blue. Bioresour Technol 114:703–706
Plunkett KN, Zhu X, Moore JS, Leckband DE (2006) PNIPAM chain collapse depends on the molecular weight and grafting density. Langmuir 22:4259–4266
Deng S, Ting YP (2005) Fungal biomass with grafted poly(acrylic acid) for enhancement of Cu(II) and Cd(II) biosorption. Langmuir 21:5940–5948
Huang S-H, Chen D-H (2009) Rapid removal of heavy metal cations and anions from aqueous solutions by an amino-functionalized magnetic nano-adsorbent. J Hazard Mater 163:174–179
Pal A, Giri A, Bandyopadhyay A (2016) Influence of hydrodynamic size and zeta potential of a novel polyelectrolyte poly (acrylic acid) grafted guar gum for adsorption of Pb(II) from acidic waste water. J Environ Chem Eng 4:1731–1742
Tian Y, Wu M, Liu R, Wang D, Lin X, Liu W, Ma L, Li Y, Huang Y (2011) Modified native cellulose fibers—a novel efficient adsorbent for both fluoride and arsenic. J Hazard Mater 185:93–100
Sips R (2004) On the structure of a catalyst surface. J Chem Phys 16:1024–1026
Hokkanen S, Repo E, Song L, Sillanpää M (2015) Removal of arsenic(V) by magnetic nanoparticle activated microfibrillated cellulose. Chem Eng J 260:886–894
Pourjavadi A, Barzegar S, Mahdavinia GR (2006) MBA-crosslinked Na-Alg/CMC as a smart full-polysaccharide superabsorbent hydrogels. Carbohydr Polym 66:386–395
Ekici S (2011) Intelligent poly(N-isopropylacrylamide)-carboxymethyl cellulose full interpenetrating polymeric networks for protein adsorption studies. J Mater Sci 46:2843–2850. https://doi.org/10.1007/s10853-010-5158-0
Lu P, Xiao H, Zhang W, Gong G (2014) Reactive coating of soybean oil-based polymer on nanofibrillated cellulose film for water vapor barrier packaging. Carbohydr Polym 111:524–529
Sun R, Hughes S (1998) Fractional extraction and physico-chemical characterization of hemicelluloses and cellulose from sugar beet pulp. Carbohydr Polym 36:293–299
Li G, Yu N, Gao Y, Tao Q, Liu X (2016) Polymeric hollow spheres assembled from ALG-g-PNIPAM and β-cyclodextrin for controlled drug release. Int J Biol Macromol 82:381–386
Pan Y, Cai P, Farmahini-Farahani M, Li Y, Hou X, Xiao H (2016) Amino-functionalized alkaline clay with cationic star-shaped polymer as adsorbents for removal of Cr(VI) in aqueous solution. Appl Surf Sci 385:333–340
Royer B, Cardoso NF, Lima EC, Vaghetti JCP, Simon NM, Calvete T, Veses RC (2009) Applications of Brazilian pine-fruit shell in natural and carbonized forms as adsorbents to removal of methylene blue from aqueous solutions—kinetic and equilibrium study. J Hazard Mater 164:1213–1222
Yao Y, He B, Xu F, Chen X (2011) Equilibrium and kinetic studies of methyl orange adsorption on multiwalled carbon nanotubes. Chem Eng J 170:82–89
Zhou C, Wu Q, Lei T, Negulescu II (2014) Adsorption kinetic and equilibrium studies for methylene blue dye by partially hydrolyzed polyacrylamide/cellulose nanocrystal nanocomposite hydrogels. Chem Eng J 251:17–24
Repo E, Warchol JK, Kurniawan TA, Sillanpää MET (2010) Adsorption of Co(II) and Ni(II) by EDTA- and/or DTPA-modified chitosan: kinetic and equilibrium modeling. Chem Eng J 161:73–82
Ji W, Wang L, Qian H, Yao W (2014) Quantitative analysis of amoxicillin residues in foods by surface-enhanced raman spectroscopy. Spectrosc Lett 47:451–457
Piccin JS, Dotto GL, Pinto LAA (2011) Adsorption isotherms and thermochemical data of FD&C Red noã 40 binding by Chitosan. Braz J Chem Eng 28:295–304
Garnier C, Finqueneisel G, Zimny T, Pokryszka Z, Lafortune S, Défossez PDC, Gaucher EC (2011) Selection of coals of different maturities for CO2 storage by modelling of CH4 and CO2 adsorption isotherms. Int J Coal Geol 87:80–86
Kara M, Yuzer H, Sabah E, Celik MS (2003) Adsorption of cobalt from aqueous solutions onto sepiolite. Water Res 37:224–232
Sparks DL (1989) Kinetics of soil chemical processes. Environ Soil Chem 62:149
Ho YS, Mckay G (1999) Pseudo-second order model for sorption processes. Process Biochem 34:451–465
Pang Y, Zeng G, Tang L, Zhang Y, Liu Y, Lei X, Li Z, Zhang J, Liu Z, Xiong Y (2011) Preparation and application of stability enhanced magnetic nanoparticles for rapid removal of Cr(VI). Chem Eng J 175:222–227
Manna B, Ghosh UC (2007) Adsorption of arsenic from aqueous solution on synthetic hydrous stannic oxide. J Hazard Mater 144:522–531
Li Y, Xiao H, Chen M, Song Z, Zhao Y (2014) Absorbents based on maleic anhydride-modified cellulose fibers/diatomite for dye removal. J Mater Sci 49:6696–6704. https://doi.org/10.1007/s10853-014-8270-8
Wang J, Zhou X, Xiao H (2013) Structure and properties of cellulose/poly(N-isopropylacrylamide) hydrogels prepared by SIPN strategy. Carbohydr Polym 94:749–754
Chen S, Zhang J, Zhang C, Yue Q, Li Y, Li C (2010) Equilibrium and kinetic studies of methyl orange and methyl violet adsorption on activated carbon derived from Phragmites australis. Desalination 252:149–156
Tokuyama H, Yanagawa K, Sakohara S (2006) Temperature swing adsorption of heavy metals on novel phosphate-type adsorbents using thermosensitive gels and/or polymers. Sep Purif Technol 50:8–14
Acknowledgement
This work was financially supported by the National Natural Science Foundation of China (Grant No. 21306024), the Natural Science Foundation of Fujian Province (Grant No. 2016J01208), the Special Fund for Science and Technology Innovation of FAFU (Grant Nos. KFA17217A and KFA17476A), and New Brunswick Innovation Fund (NBIF) and NSERC Canada.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
There is no conflict of interest.
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
About this article
Cite this article
Zhang, M., Li, Y., Yang, Q. et al. Adsorption of methyl violet using pH- and temperature-sensitive cellulose filament/poly(NIPAM-co-AAc) hybrid hydrogels. J Mater Sci 53, 11837–11854 (2018). https://doi.org/10.1007/s10853-018-2342-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10853-018-2342-0