Abstract
Material extrusion process, or commonly known as fused deposition modelling (FDM), is the most popular additive manufacturing process to date. Most universities use this technique along with PLA and ABS as the main materials for prototyping. A lot of wastes are generated in this process from support structures and scrapped parts, but they are not usually recycled indoor. Most commonly, these materials are thrown away as landfill. Therefore, the aim of this research was to investigate in-house recycling of PLA wastes using a standard desktop filament extruder. A total of two cycles were carried out (Cycle 0 being the new filament, Cycle 1 and Cycle 2). Mechanical properties, thermal properties and melt flow rate (MFR) were tested on the obtained samples at each cycle. After one recycling (Cycle 1), mechanical properties reduced drastically. This was attributed to hydrolytic degradation which is shown through an increase in MFR and percentage crystallinity. Increasing MFR can be attributed to the reduction in PLA molecular weight. Besides degradation, there were some extrusion and printing issues, which were magnified during Cycle 2. The clogging of extrusion nozzle was due to impurities as no filtering was used during extrusion. Overall, it can be concluded that in-house recycling is feasible, but it should be done with care as the resulting material has reduced mechanical properties.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Vink ETH, Rábago KR, Glassner DA et al (2003) Applications of life cycle assessment to NatureWorksTM polylactide (PLA) production. Polym Degrad Stab 80(3):403–419
Żenkiewicz M, Richert J, Rytlewski P et al (2009) Characterisation of multi-extruded poly(lactic acid). Polym Test 28(4):412–418
Scaffaro R, Morreale M, Mirabella F et al (2011) Preparation and recycling of plasticized PLA. Macromol Mater Eng 296(2):141–150
Anderson I (2017) Mechanical properties of specimens 3D printed with virgin and recycled polylactic acid 3D print. Addit Manuf 4(2):110–115
Cruz Sanchez FA, Boudaoud H, Hoppe S et al (2017) Polymer recycling in an open-source additive manufacturing context: mechanical issues. Addit Manuf 17:87–105
Zhao P, Rao C, Gu F et al (2018) Close-looped recycling of polylactic acid used in 3D printing: An experimental investigation and life cycle assessment. J Clean Prod 197:1046–1055
Kong Y, HayJN (2002) The measurement of the crystallinity of polymers by DSC. Polymer (Guildf)
Deroiné M, Le Duigou A, Corre Y-M et al (2014) Accelerated ageing of polylactide in aqueous environments: comparative study between distilled water and seawater. Polym Degrad Stab 108:319–329
Wang S, Capoen L, D’hooge DR et al (2018) Can the melt flow index be used to predict the success of fused deposition modelling of commercial poly(lactic acid) filaments into 3D printed materials? Plast Rubber Compos 47(1):9–16
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Ong, T.K., Choo, H.L., Choo, W.J., Koay, S.C., Pang, M.M. (2020). Recycling of Polylactic Acid (PLA) Wastes from 3D Printing Laboratory. In: Emamian, S.S., Awang, M., Yusof, F. (eds) Advances in Manufacturing Engineering. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-15-5753-8_67
Download citation
DOI: https://doi.org/10.1007/978-981-15-5753-8_67
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-15-5752-1
Online ISBN: 978-981-15-5753-8
eBook Packages: EngineeringEngineering (R0)