Abstract
It has been shown after several studies, that in view of the need to strengthen the deficient columns of reinforced concrete (RC), one of the most attractive and used techniques to increase strength and strain capacity, is the confinement of concrete whit FRP (fibre reinforced polymers).
It is well known that the confinement of square or rectangular columns is less efficient than the confinement of circular columns.
Most of the experimental studies focused on the behaviour of small-scale concrete circular specimens. However, in practice, the most typical findings are the square / rectangular columns of reinforced concrete (RC) on a large scale, so that there is still significant uncertainty in the models used to calculate the reinforcement with FRP and their applicability (especially in the case of columns with rectangular section).
One of the key parameters in the prediction of the models is the ultimate strain of the FRP. Some models consider a strain efficiency factor of approximately 0.6, the value of which has been determined from tests on small-scale cylindrical specimens.
This paper presents an analysis of the design formulations proposed in the main published international guidelines and compares them with the experimental results of larger square and rectangular section specimens (intermediate and full scale).
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
American Concrete Institute ACI-440.2R-17 (2017) Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures, Farmington Hills, Michigan
Concrete Society TR55 (2012) Technical Report Design guidance for strengthening concrete structures using fibre composite materials, 3rd edition, UK
Coonan RM (2016) Experimental Testing of Realistically Sized and Loaded FRP-Confined Prismatic Reinforced Concrete Columns. Ph.D. Thesis University of Bath
Demers M, Neale KW (1999) Confinement of reinforced concrete columns with fibre-reinforced composite sheets–an experimental study. Can J Civ Eng 26:226–241
Fédération internationale du béton. fib Bulletin 90. (2019) Externally applied FRP reinforcement for concrete structures
Janwaen W, Barros J, Costa I (2019) A new strengthening technique for increasing the load carrying capacity of rectangular reinforced concrete columns subjected to axial compressive loading. Compos B 158:67–81
Lam L, Teng J (2003a). Design-oriented stress-strain model for FRP-confined concrete. J Constr Build Mater 17(6, 7):471–489
Lam L, Teng J (2003b) Design-oriented stress-strain model for FRP-confined concrete in rectangular columns. J Reinf Plast Compos 22(3):1149–1186
Matthys S, Toutanji H, Audenaert K, Taerwe L (2005) Axial load behavior of large-scale columns confined with fiber-reinforced polymer composites. ACI Struct J 102(2):258–267
National Research Council, Advisory Committee on Technical Recommendations for Construction, CNR-DT200_R1 (2013) Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Existing Structures. Italy
Rocca S (2007) Experimental and analytical evaluation of FRP-confined large size reinforced concrete columns. PhD. Thesis. University of Missouri-Rolla. Rolla, MO, USA
Toutanji H, Han M, Gilbert J, Matthys S (2010) Behavior of large-scale rectangular columns confined with FRP composites. J Compos Constr ASCE 14(1):62–71
Zeng JJ, Lin G, Teng G, Li LJ (2018) Behavior of large-scale FRP-confined rectangular RC columns under axial compression. J Eng Struct 174:629–645
Acknowledgements
This work is part of research project BIA2016-80310-P funded by the Spanish Research Agency (AEI) and the European Regional Development Fund (ERDF) and Project PIE-202060E267 funded by the Spanish National Research Council. V. J. Castro acknowledges the financial support (FPI grant BES2017-080647) of the Spanish Ministry of Science and Innovation and the European Social Fund.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2022 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Castro, V.J., de Diego, A., Martínez, S., Echevarría, L., Gutiérrez, J.P. (2022). Key Parameters in the Calculation of the Reinforcement of Rectangular Columns with FRP. Review of Design Guidelines and Comparison with Experimental Results. In: Ilki, A., Ispir, M., Inci, P. (eds) 10th International Conference on FRP Composites in Civil Engineering. CICE 2021. Lecture Notes in Civil Engineering, vol 198. Springer, Cham. https://doi.org/10.1007/978-3-030-88166-5_44
Download citation
DOI: https://doi.org/10.1007/978-3-030-88166-5_44
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-88165-8
Online ISBN: 978-3-030-88166-5
eBook Packages: EngineeringEngineering (R0)